Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hello
I use nrf52832 SDK14.2 for development, I copy the flash_fstorage example code to my project.
I write the data to flash doesn't have any error, and can read flash...
Hi,
I am evaluating different advertising setups which can be easily created with nrf-connect-ble plugin for nrf-connect-desktop (Windows 10) with a nRF52840 dongle.
I...
Hi ,
SDK: nRF5_SDK_15.2.0_9412b96
IDE: SEGGER Embedded Studio V4.12(64bit)
C language standard: gnu99
code:
u32 nums_hf __attribute__((section(".non_init"))...
So I have a question about the nRF9160 when enabling the xDRX or PSM mode. Does one just turn the option on and leave it on eaven while uploading data or do you turn it off...
Hello Nordic Support Team
I am using proxy client and server example with nrf528232 dk board.I can send messege from client node to all server node successfully but i want...
In our product we have implemented buttonless DFU over BLE with the secure boot-loader (unbonded) on SDK 15.2. The bootloader is unmodified except for the addition of PA/LNA...
When I compile the program times an error :
.\_build\nrf52810_xxaa_s112.axf: Error: L6366E: uECC.c.o attributes are not compatible with the provided attributes . Object...
I am trying to run the SPI code on an NRF52382 based custom board. I am using the NRF 52 DK, Keil uVision 5.0 , SDK 15.2.
I cannot set and clear the SPI relevant pins...
I am evaluating the nRF52840 for developing wearable tech that would implement some basic sensors such as GPS & pedometer. Just have a couple questions regarding the transition...
Hi all,
I am sorry if this is a rookie question. I had researched and tried the methods shown online, including:
added $(ProjectDir)/flash_placement.xml to the linker...
Hi
I am working on nrf52840, try to create a service,so i follow the tutorial , but i got a problem. The DK doesn't advertise, when I debug it, then it will jump into this...
Hi,
I manged to successfully run the mesh DFU example, however i noticed one unusual thing. I was expecting device to revert to old version of firmware, if in case the...
Is there an example somewhere to show how to use the "BLE_APPEARANCE_GENERIC_HID" to transfer data over BLE to a another BT device such as a laptop ?
The HID mouse and HID...
Hi,
I have a use in mind for a Nordic part, probably the nRF52810. It would be nice to have an input on one pin act as an output enable for several other pins, i.e. when...
