I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I use nrf52832 board, S132,SDK14.2 . I refer to some projects and nrf52 datasheet that indicate to use pin sensing mechanism( level trigger ) to wake up device from system...
We are using Nordic SDK version 15.2, and have successfully implemented many functions using the CLI API but are stuck on how to secure the CLI. We have a USB and RTT CLI...
Hi,
I am working with two nRF52840 DVKs and the 802.15.4 example "wireless uart" from the SDK v15.2.
I flash both boards, and both of them get initialized (LED1 ON). Then...
We program the nRF52840 with a Segger tool at 8MHz.
The programmation time for 400kB is 13s (0.5 erase, 2.3s soft device and 8s application).
When we reduce the frequency...
The customer's goal is to play a tone on an external speaker with a data rate of 11.05KHz.
The "default" demo code for the Thingy52 @ https://github.com/NordicSemiconductor...
Hi all,
I just migrated from sdk 14.0 to sdk 1.52, and now I'm running into a problem while testing my codebase with ceedling. When testing my delay module, which uses nrf_delay...
Good morning,
We are making our first PTS test to certyficate our BLE device. I have question regarded to test name GAP/DISC/NONM/BV-02-C. Our LE device plays the Peripheral...
Hi:
I download nordic example.But i can not know how ZBOSS zstack form a network.
I try to use bdb_start_top_level_commissioning(ZB_BDB_NETWORK_FORMATION ) and it can...
Hi there,
I'm just beginning BT development, so sorry for my basic question:
Our application needs to transfer data from PC to our device (approx. 512 bytes) then our...
Hi
I have tried to enable bonding on a application based on the Running Speed and Cadence example (Both peripheral and central). (I could not find an example with bonding...
I want to send data from Nrf52840 dk. I want to receive the data sent on nrf24l01, which is connected to the Arduino Uno card. So I want Nrf52840 to communicate with Nrf24l01...
Hi,
downloading works fine now from SES. But now I like to use some of the ANT example projects. Im told to install SoftDevice package before downloading the example firmware...
I'm modelling a complex system with multiple BT devices based on the NRF52 using a very detailed model of the RF.
The system is based on the NRF52 using the mesh stack to...
Hi everybody!
My goal now is to use nRF52832 as a intermediary for an update package. In other words, my goal is to send a file (probably .zip package) to a board and save...
Hi,
When running the unit tests for Mesh SDK 3.1.0 I get the following failures.
83/92 Test #83: generic_dtt_client ...............***Failed 0.00 sec
From the log I...
