I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello everyone,
I am having a problem with powering my nrf51822, I have 2 Li ion batteries to power my nrf51822 and a stepper motor, I put the batteries in series to have...
Hello,
Kindly asking for some guidance... We're working on a solution that requires us to distribute unique data sets (i.e., each nodes gets a different data block, approx...
I am using sdk15 with softdevice 6.0.0 for proximity profile. By keeping bootloader as stable can I change the location of softdevice?? I want to use bootloader at the 0th...
Hi!!
I changed the example of SDK14.0.0's ble_app_uart and I am doing low power consumption.
I used timer interruption and now I am driving with power consumption of 1...
Hi all, I am working on a mesh project. I've read Mesh Technology Overview written by Martin and I wonder what will happen if a node receive two or more messages at the same...
Hello,
I'm developing a BLE application using nRF52 based on SDK15.2 using Sofdevice S132 under Windows.
The nRF52 is used to send data in notification Format. In...
hi....
i am using nrf52832 and peripheral device , microcontroller should run continuously , nrf should be in turn off mode and it should turn on when the data need to send...
Hi all,
We are using nrf52832 board in our product. We used serial dfu method to upload the bootloader. Its done with help of nRFgoStudio application.
We want to know...
Is achieving a data length of 251 possible in SDK 14.0.0, SoftDevicve S132 5.0.0 ? I tried updating my GATT table to 6000 bytes and my NRF_SDH_BLE_GATT_MAX_MTU_SIZE to 251...
Hello all,
I would like to know if anyone is willing to share nRF drivers for ADS1298.
There seems to be a Github repo containing drivers for ADS1298 with arduino.
Has...
hi engineer: I use the software version: SDK15.2; the hardware IC is nRF52832; the protocol stack is s132_nrf52_6.1.0_softdevice; when I add "init.advdata.p_manuf_specific_data...
Hi,
After configure IO and RTC I tried to enter into low power mode however the current consumption doesn't decrease until I call again __SEV (); / __WFE (); / __WFE ();...
I am working on a project where I need to transfer the data from nRF52832 to ESP8266 through UART. I made the connections RX to TX and TX to RX.
I am using ble_app_uart_c...
Hello.
I am testing example 'usbd_msc_pca10056' of ' nRF5 SDK v15.2.0 '.
I don't realize how to change the size of the 8 MB mounted device with QSPI from external flash...
