Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hi,
I am experiencing an interesting case ( I am not sure if this is a problem indeed).
I have been trying to develop code for ISP1507 (nRF52832 PC10040 based) on two...
Hi ,
I have tried to test the current consumption on NRF52840-DK (PCA10056).
DCDC is enabled.
RTC is running.
No BLE is advertising.
The DK is powered via USB. ...
hi，all
i got the nrf52832 dk and run the ble_app_uart example ,
but i found nothing output in jlink rtt viewer after called the NRF_LOG_INFO("UART Start!") ,
so could...
Hi.
I did the secure bootloader DFU. I attained step 8 in document .
I instal softdevice and secure bootloader to flash nRF52832. After make the ble_app_buttonless_dfu...
Routing the DCC pin on the nRF52832 with the chip scale package is pretty tough. The bump is surrounded on all sides by other bumps, so I don't have room for a via in the...
Hello,
I'm using nRF Connect V2.6.1 on Windows 10, I launch " Bluetooth Low Energy V2.2.0 " that uses PCA10059 Dongle as central.
Also, I have developed a peripheral application...
There are 12 LEDs which are connected using shift register HC595 ,the module used is nrf51822(bluetooth module). I want the LEDs to go off after 3 seconds interval. My code...
Hi there,
We are having issues with our boards that uses nrf52832 chip. Our first built had this chip and everything was working fine. We built a second batch and all boards...
Hi,
In nRF52832 datasheet I found that it is having internal oscillators, like 32.768Khz RC oscillator and 64MHz RC oscillator. If it is having internal oscillators what...
Hello
Most of the time we shall use the BT TX 0dBm. In special cases when we want to increase the communication distance we may select the 8dBm mode.
For RF type approval...
I am implementing long read with authorization in the server (peripheral). I have a characteristic with vlen = 1 and maxlen = 300. ATT_MTU = 23.
gatts_attr_md.vlen = true;...
Hi,
I added nRF5_SDK_15.2.0_9412b96\modules\nrfx\drivers\src\nrfx_timer.c to my project. In sdk_config.h I have:
#define NRFX_TIMER_ENABLED 1 #define NRFX_TIMER1_ENABLED...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96,PC is windows 10
I want to use the DFU to update my file,but I find that only the Init packet is signatured...
I am trying to integrate SPS30 sensor to nRF52 DK using Segger Embedded Studio. The sensor fails to initialise and the program keeps getting stuck at NRF_BREAKPOINT_COND at...
