Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello, I am using SDK15.2 on nrf52 DK with SD 6.1.0 and having an issue while sending back to back data using NUS service. I have edited the ble_app_uart application and trying...
So I am brand new at this product line, and basically new at C in general, I come from VB land. So bare with me please
I purchased both a Nordic nrf52 dev kit evaluation...
Hello there,
I'm sending IMU data (16bytes) using a notification from a custom board to a phone. My final goal is to send this packet of data (16 bytes) every 10 milliseconds...
I am developing a mobile application with bluetooth mesh.
But i can not describe the structure of a node with demo application. The sequence that I want to understand is...
Dear Nordic,
I implemented a RTC calender in nRF52832 using RTC2 . I want to port this RTC calender to nRF52810 but 810 has 2 RTC.
RTC0 is used by softdevice and RTC1...
After getting the latest nRF9160 in (DK V0.7.0) I installed pynrfjprog, and then issued the following command (as provided in the README)
nrf9160_mdm_dfu --update
...
Hi, I am new to BLE mesh. As I have understand , a provisioner is one which forms the mesh network and assigns addresses to the node and make them join to the network.
1...
Hi,
How do I-
1. Start a timer when sending data from nrf to host (PC) in form of input report.
2. When the application running on host machine receives this data, send...
When i try to add RSSI viewer app in nrf connect it shows error
Unable to install: Unable to download developer.nordicsemi.com/.../pc-nrfconnect-rssi: net::ERR_CONNECTION_RESET...
I am experiencing strange behavior on the PCA10056. I have two boards now in the same state, both were working fine before starting work on the Secure DFU (uart). The following...
I found that App timer using in ble_app_template in different modules. Is it possible to change prescaler value without harm to other modules? I need to increase maximum value...
Respected nordic community,
I am working on one project where right now i try to make custom service read operation through nrf52832 in segger studio. From my device(mobile...
HI, I am seungwoo
I am developing data transmission using nrf52810.
A 300-kilobyte file is divided into 220 bytes and transmitted continuously.
11-27 17:24:24.416...
Hi,
I'm developing a unit which i need from time to time to send a packet throw I/O lines (F.E.virtual uart)
However the packet bit timing is very critical.
As far as...
