Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have finally got FOTA working with external flash, but I have a strange problem.
When the FOTA is complete, the mcuboot fails, but the new image boots correctly.
So...
Hi, I am trying to change the USB CDC/ACM com port name. I have read through some posts but they are very short or unanswered. It seems we can change the .inf driver file...
Hello everyone. I work with nrf52840 chip and previously I had an app with softdevice (s140) and use BLE bootloader. Everything works as expected. Next I want to use another...
We are using ncs 2.6.0 and nrf5340 audio dks.
Sample is nrf5340_audio broadcaster.
One dk is configured to work as Audio Broadcast BIS Source and other as Sink. By default...
Hi there,
I am working on an audio recording and transfer application using nRF5340 (microcontroller development kit) and SPH0465 (digital microphone with I2S support...
Hello, I have designed my own board based on NRF52840-CKAA-R, which uses USB power supply. The working voltage of NRF52840 is 3.3V, and my test voltage is normal But NRF52840...
Hi,
I've ready many threads and docs on NRF52 SoC Revisions and Softdevice support but I am still confused. So apologies if I ask something which is already asked.
From...
Hi,
I want to implement low-power mode in my nRF5340 application. From what I understand, Zephyr's idle task automatically handles entering sleep modes, and the device wakes...
Hi,
I am evaluating warm and cold reboots, I am seeing no difference between them. I tried tracing sys_reboot definition, ended up with
For arm core with no handling...
As described in the docs.nordicsemi.com/.../powersave.html: “The application must choose the right duration based on the traffic pattern. Applications must also take appropriate...
Hi, I am using nrf9160 DK development board, i want to use gpio pins in this kit for a SPI interface from nrf52840, which pin i can use for this purpose. in datasheet it very...
Hello Nordic Team,
I am working on integrating the nRF21540 RF Front-End Module (FEM) with the nRF52840-QFAA in the 48-QFN package. Could you please provide the following...
Hi, I have reviewed the light_bulb app code in NCS2.8.0(include src code/CMakeLists.txt/prj.conf and so on)。 But I can't find where the path of matter is included, could you...
Hi all,
I wanted to enable read/write protection for MCUBOOT partition in my firmware from the application and encountered a strange problem. The build (build system - default...
