Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
I'm developing a new battery powered sensor device with an NRF52840 and have some thoughts about efficient power supply. The main question is: Using an external DC...
Hi,
I have opened Sample "Peripheral_hr_coded" and added build configuration.
Then I clicked on Action --> Build.
Please validate below log. Is it proper ?
Log is...
Is it possible to dynamically switch between USB CDC (Communications Device Class) mode and USB MSC (Mass Storage Class) mode on the nRF52840? If so, could you outline the...
Hi, recently I started migrating my company's firmware from nRF5 SDK to nRF Connect SDK. I have been following the devAcademy courses and so far 1. I have created my custom...
Hello, guys.
We need USB CDC ACM and UART driver with DMA to run in parallel as two different nodes in the device tree.
For that purpose, here is what we have in the prj...
This is a general question about selling our modem-enhanced products internationally. We use an NRF9160 (NB-IoT), but we have some of our devices equipped with older Telit...
Hello,
NAS-RAI (Non-Access Stratum RAI) used on NB-IoT Control Plane : on nRF9160 it was controllable via the AT%XRAI command, using the <rai> parameter :
0 – Undefined...
SOC: NRF52840
SDK : NRF conenct SDK 9.11
Application Gateway
we had end devices to join the network which is whitelisted in the coordinator ; so please can you let...
aliexpress.com/.../1005007557383132.html
I bought the above board I checked the revision information with nrjfprog --deviceversion and it was revision 1 All functions including...
I'm using the nrf52840, and I'm doing a project where the system needs to sleep for a long time, maybe more than 24 hours. Following this ticket, to go to sleep I just do...
Hi
I'm working on understanding how whitelist filtering is implemented and works in Bluetooth Low Energy. I'm currently following Exercise 2 in Lesson 5 of DevAcademy's...
Hi, We are working on power optimization for our project which uses nRF5340 board. Upon testing we observed when starting hardware timer the base level of the current consummed...
My custom board with a NRF5340 (MDBT53-1M) with LF crystal is running as a central on NCS 2.6.1.
It's connecting to a legacy device which has a BLE121LR.
NRF5340 centrals...
Hi,
I use vs code to run nRF9160 DK applications and it runs fine for a month. But recently I cannot build configuration even in an empty application . Old good applications...
