hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
i have a nrf52840dk that is flashed with a old program i used. i want to try the nfc tag and read it using my phone. what should i flash to my nrf52840dk in order to use it...
Hello,
I am building the existing WIFI station app for the Thingy53 with the nRF 7002EB board - sample code: nrf/samples/wifi/sta
In the CMakeLists.txt file, the line...
Hi,
we are now using nRF Toolbox -> Logger tool on our phone to monitor Thingy91 application information via UART/BLE.
Now we would to monitor/log the same information...
Hi,
I am using NCS v2.4.2 and nRF5340DK + nRF21540EK but I can not enable GPIO+SPI mode.
for example, I use nrf/samples/bluetooth/central_and_peripheral_hr application...
I manage to connect to the network and disconnect from it after sending the data, but if I'm in an area without reception, the device tries to connect and after a while, the...
: Chip Not Recognized by J-Link
I need advice from someone familiar with the nRF9160-SICA-B1A-R7.
I purchased an nRF9160-SICA-B1A-R7 chip individually from Digi-Key and...
Dear Sir :
We are now developing on nrf52840, with ncs v2.6.1 and zephyr.
We want to put I2C0 to PM_DEVICE_ACTION_SUSPEND before sys_poweroff().
Our code is below :...
Hello everyone,
I am currently trying to get a ML model running on my nRF52 (preferred nRF52832 but nRF52DK works also for me). Right now I am trying to evaluate if my setup...
We have using nrf5340-nrf7002 in our custom board. SDK version 2.6.1 We understand that the timer will not function in System OFF (deep sleep) mode. However, our project is...
Hi there,
I've encountered a strange PWM behavior and have investigated a bit. When setting load_mode to NRF_PWM_LOAD_WAVE_FORM, creating two sequence, and the latter sequence...
Hello, We want to build our own custom protocol because the features we need are not available from existing protocols like BLE or Zigbee etc. But it is beyond our reach to...
Hi all,
In my application I need to use some of the NET core peripheral from the APP core (since I ran out of peripheral instances in the APP core). According to this page...
I am running into an issue (title), where I am attempting to switch the advertising interval to a slower interval after a set period of advertising in order to save power...
Hello everyone,
I'm trying to test the ble_app_uart example. When I download the code into the 52DK, i can see my device show up as a possible connection, but when i connect...
We have a number of fixtures using nRF52 DK boards to both flash a custom board and to do a DFU operation to that board. We use a SPST switch in the P19 pin 1 lead in the...
