Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I have an issue where my PC suddenly can't use any JLink after it had previously been working. Nothing changed to my knowledge that would have caused this issue other...
Hello,
I'm trying to enable the Power management for nRF9161 over nRF-Connect SDK2.5
the prj.conf has an entry of 'CONFIG_PM=y'
but it not accepted because we do not...
I've received a Nordic Semiconductor nRF9161 from a friend, who has been using it for a while.
I would like to completely reset the module, as it came when bought, so...
Im trying to use the BMA4xx driver (via i2c) in 2.7.0. The driver seems to init the device ok but I am getting a "SECURE FAULT" as soon as I do a sensor_sample_fetch . Attached...
Hi,
I spend few day trying to understand the issue with the provided sample (followed the tutorial) in the IoT fundamental lecture for the MQTT protocole. Then, I tried...
Hardware: nRF52840 (Custom Hardware)
Software: nRF Connect SDK v2.6.1
I am using the nRF52840 with custom hardware, where the device operates in two modes: Sleep Mode...
Hi,
In my project, I need turn on/off the hfxo, I found when i configure the hfxo, the nfc is not working. Here is my code:
void gps_server_function ( void * p1 , void...
HW: NRF52832 DK SDK: 17.1 SD:S132_7.2 Sw: ble_uart_c Issue: nRF52832 as a central to scan a peripheal(not nordic chip),the nRF Connect APP can discovery all the service, but...
I am trying to connect RPI(and/or Nvidia Jetson) with nrf9160 custom board(Icarusv2). I am using this custom board for other purposes and it works fine. For now I found only...
Hei,
I need to find the documentation for the NRF SDK 1.8, there's a page which has links to all the documentation versions:
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I am working with nRF52840 SoC (custom board) and AT25QL641 QSPI Flash chip. I am on v2.1.0 of nRF Connect SDK. The slot1 (update slot) is on an external flash.
...
I am using the serial port of SDK7.1 to send and receive data, and this serial port is a serial port of nRF51_SDK_7.1.0\examples\peripheral\uart\pca10028\arm. Can this serial...
Hi,
I have a project using Zigbee and NRF5340.
I'm facing a "zboss_osif ZBOSS fatal error occurred" from ZBOSS lib after few days of operation.
I'm wondering if the...
Hello,
first I would like to "set the scene".
* hardware : cutsom board
* mcu : nrf52832
* nRF5_SDK : nRF5_SDK_17.0.2_d674dde
* software : mbr + bootloader + softdevice...
Dear Sir/ Madam,
What is the difference between:
> nRF2401P and
>nRF2401P-R ?
Also, code that is written using nRF2401P - would it still work when using nRF2401P...
