I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
We are currently using a Linux system and controlling HCI_UART firmware through BlueZ.
The problem we are encountering is that using BlueZ V5.55 allows normal Bluetooth...
Hello! I have a GATT Server in the form of a nrf52840-DK that has been given to me from a company that has a custom service on the server using CCCD. I have the full documentation...
Hello,
I would like to know if using a self made GATT Custom Service in HID Device (NRF Desktop App) can incur additional costs during the Bluetooth qualification process...
Hi,
I am working on a project using the nrf52840. For legacy reasons we are using Nordic SDK version 15.3.0 and SoftDevice S140 version 6.1.1.
I am trying to maximise...
I need help . i am confused that if we send the audio data then it follow which of the following order ? input ->BLOCK ->FRAME->LC3CODEC->SDU->PDU OR input-> BLOCK->FRAME...
We need to establish connections to muliple of our products (they use nRF52832/nRF52840) parallel from our Android/iOS apps to send commands which are time critical (in relation...
Hi,
I am getting an error when trying to enable the Fast Pair (SDK 2.7.0) using the bt_fast_pair_enable() function.
I debugged this error and I saw that it's caused when...
Hi,
I am developing an application which needs a precise reference clock of 20ms. I have a 32MHz Xtal on the PCB with a tolerance of +-10ppm. To configure the device to...
Hi
I'm using nrf toolchain/sdk 2.5.2.
Got a strange problem with my QSPI NOR flash interface. when i run flash_erase i get error message "qspi_nor: Failed to schedule...
I am running a nrf5340 with zigbee as a coordinator, I observed after a while that battery life of my end devices don't last as expected. Then after debugging I found that...
Hi Team,
We are developing a custom board using nRF52840 SoC. We need the storage and handling of IC, reflow solder profile of IC and assembly instructions if any.
Regards...
HI currently i am utilizing sdk ver 17.1.10 nrf52840 s140 we are using dfu/secure_bootloader/pca10056_ble app and i need to add UART app to it so that so we need both bootloader...
hardware:nrf5340+npm1300
software:ncs 2.5.1
hi professor,
If I just connect VBUS, The npm1300 will reset when I read bulk register. If I connect vbat and vbus, read...
In NRFX Oscillator header , accessing the function requires the preprocessor macro which in turn requires preprocessor conditional
The problem is that final conditional...
Hi, I am developing firmware for a project using a custom board with the nrf52832. The project requires mcuboot and secure BT OTA. When I enable the configs
CONFIG_BOOTLOADER_MCUBOOT...
