I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
I'm updating the NCS we are using from 2.0.2 to 2.1.0 in order to use the modem firmware 1.3.3 that was just released. I verified my build with NCS 2.0.0, 2.0.1 and 2.0.2...
Hello!
I use NRF Connect SDK 1.8.0, but peripherials are configured using nrfx library.
My task is to implement serial interface where I have PIN_TX and PIN_RX. I transmit...
Hello All,
I have few questions below:
- Does the ENABLE input disconnect the internal power systems completely, or does the circuit remain in some mode and nevertheless...
Hi Sir,
I am testing the NDT w/ example "nRF_DM" (NCS 2.0.0), there are two nRF52840-DK for this test. When two boards link success, the terminal starts to show the log...
Hello everyone
In the company I work for, we make a special kind of dongles which are able to connect to smartphones through BLE and transfer data.
I have 4 of these dongles...
Hi there,
I am working on a door lock project using nRF 52840 DKs and nRF5 SDK for Thread and Zigbee v4.2.0. we are having both ZigBee and BLE protocols in it. I started...
Hi everyone,
I'm trying to implement directed advertising on the BLE codeded PHY.
My setup of consists of two identical NRF5340 based custom boards, running FW based on...
Hi, nice to e-meet you. I want to use nRF52810 pin 25 (or other pins) to drive an external board, and through it to control the external board switch.
I set the pin to H0H1...
Hello,
I am currently working with pc-ble-driver-py and have observed write operations taking an exceedingly long time. Previous DevZone posts on this topic seem to be unresolved...
Hi,
Sorry to seek help again but I cant solve this issue
Steps
1 - nrfjprog -f nrf52 --eraseall
2 - nrfjprog -f nrf52 --program mbr.hex --sectorerase --verify
With...
Hi,
I've got a GPIO interrupt callback that collects an ADC reading. All is fine until there.
But when interrupts become numerous (~3/5k triggers / sec), a MPU FAULT...
Hello. I'm relatively new to zephyr and working with nrf's and I'm experiencing a modem error when running the mqtt_simple sample project that I cant resolve. Upon booting...
Using the Zephyr logging system, setting Kconfig option in prj.conf to override logging to level 4 (output LOG_DBG messages) breaks the console and no output is sent at all...
