I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
Hello,
I am trying to send status messages to a Client model with a specific unicast address on one node. This node's parent element has both generic onoff server and client...
When i define macro
CONFIG_LOG =y
i want to use log
The program can not build successfully
FAILED: zephyr/zephyr_pre0.elf zephyr/zephyr_pre0.map cmd.exe /C "cd...
Hi,
I am trying to send the data received over BLE from nrf5340 to ESP32 and then from ESP32 to nrf5340 using UART communication using below configuration.
nRF5340 esp32...
Hi
I'm wrkig with nRF5 Software Development Kit v17.0.2 and BLE Mesh. When the device is running, after some hours of operation, the NRF_FAULT_ID_APP_MEMACC is getting triggered...
Hi,
I am using nRF connect SDK V2.0.2 chipset 52832 built using VS code.
Need to move the setup from an external clock to an internal RC oscillator.
When I disable ...
The following Pin definitions for QSPI result in Errors during build using NRF Connect SDK. This exact configuration is working on a custom design using nRF5 SDK using the...
I want my client to advertise forever so I added the following code:
static void ble_evt_dispatch(ble_evt_t * p_ble_evt)
{
ble_conn_params_on_ble_evt(p_ble_evt);
ble_nus_on_ble_evt...
Hi,
My device was designed with SDK 15.0, the APP_ADV_DURATION is set to 0 in order to have the device in advertising for all time.
Now I try to use the SDK 15.3 but when...
I've got an embedded application where I want to stream from my device to wireless headphones. Really looking for legacy (I think) right now as I'm not sure LE audio is supported...
I'm getting an occasional MPU fault on the nRF52840 on the Thingy91 when starting scanning:
Running arm-none-eabi-addr2line leads me to
buf->len -= len;
in...
Hi,
I am working on PWM and i am using bellow function for pin set cycles and it's working fine as per Duty cycle and frequency
i am getting the wave form also but i'm...
Hi All,
Is macro in /modules/nrfx/hal/nrf_rtc.h correct?
/** @brief Macro for converting expected frequency to prescaler setting. */
#define RTC_FREQ_TO_PRESCALER...
When compiling without a pm_static.yml in my project and using the dynamic partition resolver with mcuboot I noticed that I get an overflow error.
The current accepted fix...
hello
I am using ufl(U.FL-R-SMT(01)) 50 ohm antenna
My question is: is the matching circuit listed in the picture sufficient or do I need another component
