Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello, I'm trying to get FOTA over BLE (SoC & external Flash) working on NCS 2.9.0. The sysbuild and MCUboot configurations and overlays seem to be fine. The application builds...
Hi,
I've started working with the nRF52-DK for developing a new product based on the nRF52832. I'll be using custom services so I took as a starting point the projects provided...
Hi,
I'm using Linux with Visual code extension to compile for both nrf52840DK and nrf52480 dongle and I'm using the programmer in nrfConnect to write to the devices. The...
This case don't happen when i merged net_core and app_core to burn . I used to burn only one core.
What causes this?
Now I have a new question.I use one nrf5340 as CIS...
I am using nRF connect SDK and wanted to examine gpio 'out' register during the debugging session but every time I try to print the register value, I get the following error...
Hi,
I am using the SDK 2.1.1 and I will upgrade to 2.1.4 since errata 160 is fixed there.
Reading the errata document here , the anomaly 168 is fixed in SDK 2.5.1. Unfortunately...
Dear nRF support,
nRF5340 custom board
nRF NCS 2.5.x
Running into this very weird issue:
Program runs fine if I don't attach debugger to it
When I do "attach to...
Hello Nordic Engineer,
I successfully controlled the 52840 DK through Mesh using my phone. However, after exiting the app and reopening it, I can no longer control the...
Hello Team,
I’m working on implementing BLE Mesh on the nRF52832. I extracted the BLE Mesh ZIP file and placed it in the same directory as the nRF SDK. Then, I opened the...
Dear Nordic Support Team,
I am encountering an issue with the nRF52 SDK for Mesh v5.0 and nRF52 SDK v17.0.2 while running the serial example. The system runs for a while...
Hello,
In the header file nrf54l15_types.h, we see the following defines related to the SAADC:
* REFSEL @Bit 12 : Reference control */
#define SAADC_CH_CONFIG_REFSEL_Pos...
Errors on calling "lte_lc_init()"
Does anyone know what the corresponding error codes mean, or what could be done to debug the cause?
Thank you very much.
I am writing an i2s application for the nRF5340 Audio DK with toolchain and nRF Connect SDK v2.9.0.
During development I noticed that nrfx_i2s_start() does not seem to check...
Hi,
I am working on a project where I have two separate physical devices , each based on an nRF52832 :
One device is a BLE Mouse
The other is a BLE Keyboard
My...
