Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I am running peipheral_uart sample with nRF connect 1.9.1 . After running the sample for 10-15 min, I start getting the following error
"Not able to allocate UART...
I am unable to achieve low power after I enable UART. I disabled UART0 after enabling and the UART0 registers are all getting its default value after disabling.
But the...
Is there an HCI API to control the device and configure it to work with LE Audio? If so, is there an example of minimal configuration that will allow Audio DK to transmit...
I'm trying to integrate my application with the LWM2M Carrier library, and experiencing a hard fault when calling date_time_update_async(). This happens even if I call the...
After creating a new Ubuntu virtual machine to start fresh, I am still experiencing the issue below.
I re-installed the Connect SDK manually on the new virtual machine as...
Hi, I am trying to implement spi or i2c communication with a sensor using dma in master mode. can anyone give me some sample code on how to get spi/i2c peripheral over easy...
We designed an industrial gateway to communicate with sensors through Bluetooth. Both use nrf52832 chipset. However, there are many Bluetooth signals on the customer's site...
Hello,
I have a pure-C library that I'd like to build, and then import into another project that targets the nRF52832 (nRF5 SDK v16.0.0). The library has no dependencies...
Starting a new ticket since now I have a bit more details to describe what's going on
I have a custom model server that is configured to publish every 10 seconds with retransmit...
Hello. I can't program the nRF5340 of a couple of boards I recently received. I have it powered via USB (5V), and nRF_VDD is powered up to 1.8V as expected.
I've probed...
Hello,
In my project i am using stepper motor with nrf52840 and here i want to control the motor speed like in my application i want to expel fluid from the tube by pushing...
Dear sirs!
I need that timer (for example timer 3 or 4) will generate interrupt each 5 ms very precisely with precision of crystal (20 ppm). In 10 hours I cannot allow deviation...
been having issues trying to get LittleFS to work on external SPI NOR Flash. I get linker errors leading me to believe something is missing in a config. I’ve looked at many...
I previously was evaluating the basic nRF5340 DK and installed the toolchain manager and the nRF Connect SDK v 1.9.1.
I now am looking at the Audio DK, and its documents...
Dear ,
I am using nrf52833dk configured as nrf52820 using NCS1.7.0 SDK. I am experiencing some difficulties in regard to the SPI.
I have configured SPI as followed, but...
