Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Whilst I recognise some of the NC pins on the nRF52833 are IO pins on the 52840, but I also noticed apin mapping difference on a common port...52833 A16 is P1.05 and whilst...
We are using SDK 15.3.0 and S140 v6.1.1 SoftDevice. We are using an external LF crystal with tolerance of +/-20ppm, and are therefore using
#define NRF_SDH_CLOCK_LF_SRC...
Hi,
As per this link , the memory requirement of Thread 1.2 based application in nRF Connect SDK is around 487KB, over which more will be added as per application development...
I flashed a nrf52dk - nRF52832 board with a sample project (peripheral_hr) and the name is displayed correctly in the nrf connect app and other BLE discover apps.
After...
I need twoADC channels. I tried to configure using :
CONFIG_ADC= y in prj file,
&adc{ #io-channel-cells = < 0x2 >; }; in overlay file .. the compile error appears as shown...
HI
I am using VS for the firs time and I am trying to build the project Blinky but when I try to add the blinky folder to applications to build I get
: Element with id...
Hi ,
I followed the DFU-OTA tutorial(DFU over Bluetooth) given below for nrf52833dvk. and it is successfully completed. Now the query is , once we shared the bin file from...
Dear,
I need to use nRF5_SDK_17.0.2_d674dde for nRF52833.
I saw the release note, it says it need SES v4.5.
But when I use SES v4.5 to download or debug.
The computer...
Hi,
My goal is to generate a GPIO or GPIOTE interrupt and inside the ISR sample 8-bits from GPIO.
I tried modifying two sample projects to achieve this, the NRFX and...
Hi Sir,
We reference example "/nrf/samples/bluetooth/hci_uart" and test on nRF52833.
Now we want to set the Tx power by sending appropriate HCI commands from the host...
When I get the first error in UART, the receiving of new characters stops (the transmittion continue working)
and I didn't find any solution to make RX (receiving characters...
Hello
I'm about to update from NRF SDK v1.8 to NRF SDK v1.9.1. We build our firmware for both NRF9160 but also for QEMU_X86 (simulation build). I noticed that since the...
Hello, simple question regarding k_sleep(), to simplify, I've modified button example from Zephyr adding a k_sleep in button_pressed function, the k_sleep it's not working...
The Problem is occurring when I am trying to build any example project in the /examples/crypto/nrf_crypto
Here I am trying to build the /examples/crypto/nrf_crypto/test_app...
