I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
Hello!
I am able to use the Direct Test Mode application on the nRF52833 development board using the pca10100 DTM firmware found in the 17.0.2 SDK over USB. However, when...
Hello, When I use the recommended X1 and X2 crystals from Epson (Q22FA12800025 and FC-135 32.768KHZ ±20PPM,9.0PF) the device works properly, crystals from ECS did work too...
Hi,
I am doing a design with this component MP06003, but I don`t find this in the distributes in Argentina.
I am looking for this components with others distributes...
Hello Community! I've recently switched from Master Control Panel to NRF Connect. I want to use my NRF51 Dongle (PCA10031) with NRF Connect. Therfore I deleted the existing...
According to eval kit reference BOM list a TDK MLZ1608M100WDT25 10uH coil is the only one on list. Is there any other suggested coil models tested by Nordic? Just wondering...
We are designing a custom antenna for the nrf52833-QIAA. Could you supply the output impedance of the ANT1 antenna pin so that we can run an HFSS simulation on our layout...
Dear Members,
I run 3 devices,
GPS on libuarte1
LCD on SPI2
Sdcard on SPI 1,
I'm using ANT and softdevice 340,
When I run LCD and SDcard outside the main loop...
Hi,
I am having problems with the ble_advertising_int() function. It returns a return code of 12 (NRF_ERROR_DATA_SIZE) which is returned by ble_advertising_init() -> ble_advdata_encode...
Hi I ran in some problems with my BLE fragmentation. I want to send data (files) up to 6kBytes over BLE (Bluetooth 5 on nrf52840 to another nrf52840). My project is based...
I'm using PCA10056 (nRF52840 DK) for a project. First-time user, so little experience with this board.
I need 1.8v level SPI signals from the PCA10056 since I need to talk...
Hi
what is the current consumption for LPUART (when there is no event - let's say it is sleeping) on nRF9160 and on nRF52?
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello,
I have a problem regarding the connection to the cellular network of the nRF9160DK.
When I boot up the device and I have uploaded a code to connect to the network...
Hi,
We have a custom software for our custom board. And would like to investigate a little in the AT commands going to the modem and the responses
is there a config...
