Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I am trying to bring in the spi_nor driver into our project and was getting errors reading back the jedec id on initialisation so I tried to run the nrf/samples/nrf9160/http_update...
Hello, I have a problem when I enable Bluetooth on my application. If I enable Bluetooth, I can't control gpio pin on Trace DATA. If I disable Bluetooth, I can. It's a hardware...
Hi,
nRFConnect SDK Sample not working (periodic_adv _sync)
I have two nRF52840 DK with nRFConnect SDK 1.7.1
Compiled and run on nRF52840 boards:
\ncs1.7.1 \zephyr...
Hi There
Is it possible to connect to nRF Cloud using a normal 4G/LTE Sim? I see the specs of the NRF9160 show that it supports full LTE and all the Bx bands.
If the answer...
hi,
I am beginner and I am converting an Arduino library to Nordic library, but I have this part code
what is mean begin, I am confused on this part , for example , TwoWire...
Hi,
I have been programming and testing ESB on the nRF52 DK using the Arduino IDE with the sandeepmistry code base, as it allows me to view serial output to a log screen...
Hi, I'm trying to enroll my nrf9160DK preview kit in nrfcloud. I've successfully done it with my Thingy91, but in process of upgrading modem on Thingy91 with my DK I forgot...
hardware board : 52840dk_52840
sdk : ncs1.7.1
IDE: Visual Studio Code
in our OTA design , we have new image download and stored in a LTE module, since our application...
Hello,
I use ST's mcu + Atmel radio IC + nRF21540 as the FEM. Use Atmel radio IC's IO to control the TX_EN and RX_EN pins for nRF21540 automatically.
I want to change...
We plan to create a BLE central device to communicate with our peripheral devices. Both sides are based on the nRF52840 using SD140. As we've already developed the peripheral...
Hi,
I just turned off compiler optimizations with CONFIG_NO_OPTIMIZATIONS=y (before that, code was working correctly). After the change, I noticed that my program is stack...
Use Microsoft Visual Studio Installer Projects to create .msi for nRF-Command-Line-Tools-10.14.0-x64.exe and other .exe files, but an error message will appear during execution...
Hi,
Is it possible to create two separate USB devices on nRF5340? My application requires three USB classes: Audio, CDC and DFU. Currently I am using all three in a composite...
