I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi-
I am trying to debug the network and application cores simultaneously using the beacon sample application configured for RPC HOST on the nrf5340DK board. My configuration...
Hi,
With enabling of C++ support in my nCS project, i was able to include "using namespace std" and successfully build.
However, i wasn't able to use C++ std keywords...
Hello,
I'm using a nrf52832 module for my embedded device and would like to develop a pc side c++ application that is able to connect to this device using the existing Bluetooth...
modem: 1.2.3
sdk: 1.4.2 and 1.6
We have been trying to test LTE performance on different bands but so far we have not been able to use BANDLOCK to limit the connection...
Dear Members,
I got this error
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol app_uart_put (referred from retarget.o).
SDK_config.h is included,
What...
Hi
I've built a HCI USB firmware based on the hci usb example in the nRF Connect SDK for the nRF52840DK. The configuration of the project has been slightly adapter to better...
Hello,
When I try to load a simple code to the app core of the nRF5340 with Segger Embedded Studio I get an error "Failed to download application. Undocumented error"
...
Hi, I have some question about CTE.
Recently, I heard that CTE should be appended to AUX_SYNC_IND. (for connectionless use)
Is that true?
If than,
Where can...
Hi,
I noticed that in the main / master repository of Zephyr there are features that are not yet available to the version coming with NCS (for example the State Machine...
I have several out-of-tree applications targeting the nRF9160 that all build correctly when built individually. One of these applications, named "secure_partition", is a customized...
Hello,
I am working on NRF52840 DK board, trying to run Mesh DFU example code.
The issue I am facing is that I have to run Bootloader Verify python script before the...
I am using nRF52 dev kit based on nRF52832 (PCA10040). Is it possible to set the VDD output voltage to 3V or 3.3V in this? If yes, how and what header files should be added...
Until today - we have been using nRFConnect 1.5.1. We are trying to upgrade the SDK/Zephyr to nRFConnect 1.7.0.
My existing projects that use crypto interfaces no longer...
I'm trying to get my head around the steps involved in doing something as simple as accessing a GPIO pin.
I'm running VSCode as my IDE, with the nRF Connect extension (V1...
