I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I'm using the Azure Iot hub example a base for a new project I'm working on.
I've copied the example into its own folder, and can run it and connect my Azure IoT hub.
...
Hi Nordic team,
My dev environment is as follows:
nrf52840 + s140 +SD6.0.0 + SDK15.0.0 + SES + nrf52840-DK
nrf52840 is configured as BLE central with bonding enabled...
Hello,
I'm trying to use PPI over PWM to, at the end of one single PWM period, disable the PWM and switch one GPIO (later, I'll use it for more complex task, but I start...
Hello Everyone!
I am new to nRF boards and still in the learning phase. I want to send some data from nRF52840 to an LCD display through SPI. I am currently using the SPI...
Hi Nordic
One of my customer develop a system with ESB(Enhanced ShockBurst). They employs nRF51802 in their project.
In their system, above 40-50 Tx devices transmit message...
Hi Nordic Team,
I've read some forum discussion about using NAND SPI Flash Chip as external flash storage. These are two chips I'm considering :
W25N01GVZEIG ...
Hi,
We are currently trying to create a small test code to test multiple operator with different modes:
- lte-m1 or lte-nb1
- edrx 0s, 5.12s, 10.24s
- with and without...
Dear Nordic Team,
I recently ported the BLE UART example project for the PCA10056 to the PCA10059 dongle (SoftDevice 113). I added some minor changes like RX/TX pins, GPIO...
Hardware:
Raspberry Pi Zero W
nRF52840 DK running Serial Example and connected to RPi via USB
Custom nRF52840 board acting as a Vendor Model Server x 2
Software...
Hello,
I cannot find a download link for the 17.0.0_9d13099 build of the SDK. Is it publicly available and if not, can a private link be provided? Have some dependencies...
Hi,
I am using nrf52840, need to modify the bootloader to lookup a big bitmap table. But since the table is big, it cannot allocate within the bootloader Rom area.
Is...
Hi
i am using nrf9160 based custom board with zephyr, and trying to build GPIOTE with interrupt for a button, and led finally connect with PPI
i have been trying for...
Hi,
sorry if maybe I repeat the question. I have tested the central uart and the peripheral uart and I can make the two nordic nrf5340 devices communicate. I was also able...
Hi
I need help in understanding what the best practice is when retrieving messages from devices via nRF Cloud to my web APP.
I expect the devices to transmit messages...
