I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I'm developing a multi-scene application by reference to the "Light switch" example in nRF SDK for Mesh 5.0. The first screenshot show my Elements & Models structrue...
I would like to use the USB dongle with the Openthread CLI example (and eventually an open thread app) as the SDK is just too big and overpowered for my prototypes, I would...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
Hello,
I'm trying to add a rotary encoder support to the HID keyboard example on SDK17.0 with some custom hardware utilizing the NRF52840. It works well to send the requested...
Hello,
We updated NFC in our product to use SDK 17.0.2 Type 4 NFC, and we are getting customer reports that reading NFC fails on devices which used to work just fine on...
I want to create mouse&keyboard set based on nRF52810's. Keyboard that will be used is from broken laptop with 24-pin connector. Does nRF52810 have enough pins for that? ...
Hi,
I have setup a device with usbd_cdc_acm to communicate with a computer throw usb port.
First, when the device boot up and the usbd init, all works fine and the device...
Hi, I need to select a BLE+ANT SoftDevice for nRF52805. I have read link1 (All nRF52 Series Protocol Stacks) and link2 .
Questions.
1) Why I cannot find S313 from link...
Hi,
Is there any provision in nRF Connect v3.7.0 tool UI to perform uplink data transfer test scenario on Nordic nRF9160 DK ?
Please let me know if there is any alternative...
Hello,
recently i made software for peripheral with custom service and five custom characteristics and everything works just fine. Now I want to make central capable of...
Hello all I copied the peripheral>twi_scanner example and adapted it to the nRF52833 chip on our custom board. I have 4 chips (0x0b, 0x48, 0x52, 0x68) that use I2C on the...
Hello,
What's the correct way to respond to MTU requests with pc-ble-driver-js library ? on a pair of nRF52840 USB Dongles, using nRF Connect for Desktop, project based...
Using the nRF Connect mobile app for iOS (version 2.4.12) we are trying to get the MTU that our nRF5340-based device is using, however it always seems to be wrongly displayed...
I need to send data over ModBus-RTU (basically RS485) from an nRF52840. For this, I use uarte. The transceiver's transmit enable input is controlled through a GPIO pin, which...
