Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
hi
I have nRF9160 dev kit, which I am using in a LAB with a private LTE SIM card, which has 99920 PLMN ID.
The network supports Band 3, and NB-IoT is configured as an...
Hello everyone,
1st of all, thank you for taking your time to have a look over my "problem".
I have a device that I am working on, that acts as aperipheral, it is...
I modified, My application's bdaddr is set public device address. secure bootloader's bdaddr is set same public device address.
When run DFU on nrf connect for desktop,...
In my application, I am unable to read back the publish address which was configured during initialisation through mobile.
Please suggest any APIs.
Device: nRF52832
...
HI
The SDK is "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0" and I find a question that is: for all thread programs, add nrf _ delay_ ms () function in while (true) will affect...
I use a sample in NCS1.5.0 to start my project . but examples in NCS1.5.0 are single ble service .always like these: bt_conn_cb_register(&conn_callbacks); bt_enable(bt_ready_cb_t...
Hi,
1. I see the following differences between VDD1 and VDD2 descriptions:
nRF9160_PS_v2.0 P385
2. What are the differences between VDD1 and VDD2 features?
Thank...
Hi all,
I am trying transition from SDK 15.0 to 17.2 and having a branch instruction to itself (an infinite loop) which I think has something to do with the adjustment of...
I would like to create SPI clock timings using the following documents. https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fspim.html&anchor=topic
1. CSN...
I'm trying to figure out a strange issue with GPS. We have a pretty well debugged and stable system that we're adding some features to, mainly GPS. We're on SDK 1.5, using...
Hello!
I am developing an application which is connecting to an nRF52 board using the Android-BLE-Library implemented by Nordic The application is doing the following: ...
I was looking at nRF52833 as a candidate to use it as a BLE keyboard and USB keyboard (as it has USB2.0)
But in the API documentation section I see that HID keyboard is...
Hi,
I am developing a product using HA.
I am using SDK 3.0 and nRF52840 Dev-kit.
I am using the thermostat cluster, basic, time, power config, and OTA.
Along with...
Hi Devzone,
I use the original MQTT_Sample example, just change "Client ID", "Alive Time" = 120s, use NBIoT + GPS.
Development set up:
ncs v1.5.1, ubuntu, thingy91 ...
Hi,
I followed Getting Started guide for Thingy:91. However, I could not get cellular connected. I am using the iBASIS sim card came with the kit. I am located in Chicago...
