I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I want to verify below configuration can operate or not in bluetooth ?
Fitness tracker is preset in connected mode. Broadcast mode can be selected as fitness tacker have...
We have been tracking down the source of excessive power consumption that we have been seeing with the nRF52840. Our application is spending the vast majority of it's time...
Hello,
I am following a tutorial about writing a custom ble service on the NordicPlayground Github:
https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial...
I have a BLE service:
BT_GATT_SERVICE_DEFINE (lres_svc,
BT_GATT_PRIMARY_SERVICE ( BT_UUID_LRES ),
BT_GATT_CHARACTERISTIC ( BT_UUID_LRES_STAT , BT_GATT_CHRC_NOTIFY...
Hi, I have a BLE service:
BT_GATT_SERVICE_DEFINE (lres_svc,
BT_GATT_PRIMARY_SERVICE ( BT_UUID_LRES ),
BT_GATT_CHARACTERISTIC ( BT_UUID_LRES_STAT , BT_GATT_CHRC_NOTIFY...
Hi, using nrf52832 SDK 16 in the NUS example I'm working
for that, I added custom services
whenever the program running it's working fine but after some time it's automatically...
Hi,using nrf52832 SDK 16 in NUS example I'm working
for that, I added custom services
when ever program runing it's working fine but after some time it's automattically...
Iam facing mesh assert error if i call any function in super loop.
given code:
static void rtt_input_handler(int key) { uint32_t button_number = UINT32_MAX;
if (key...
I have realised the provisioner example code from nrf Mesh SDK. There I found the following set of code to be executed when i pressed button 4.
if (mesh_stack_is_device_provisioned...
Hi.
I am using Central's ble_app_uart_c_pca10028_s130 which is a sample of nRF51822.
I would like to see the timestamp of the advertisement acquisition I receive from...
Hi,
NRF52840 datasheet section "5.4.4.2 64 MHz crystal oscillator (HFXO)" mentions crystal tolerances being dependent on packet size.
It is not clear to me, what layer...
Hi,
I've had the nRF52 and Segger Embedded Studio on my old computer. But the old computer is dead now.
I am trying to create the same environment on my new computer....
Hi nordic
I run the HID keyboard with SDK 15.2 and connected to IOS's nrf conncet.
but i can't see the HID service in the table.
how can i use the nrf connect to debug...
Hello there,
I'm ripping my hair out hear reading everything I can to get the non volatile memory reading and writing.
I have a nFR52840 dongle and I dont want to...
