I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Nordic：
We need to do a communication certification, we need NORDIC to provide S112V6.1.1 QDID: 125078 certification report certificate。
thinks
jermi.jin
2021.061...
My CMD.EXE is copied here, it shows the command I'm trying to run, and the output of the program. As you can see, there is no error message.
However, it does not succeed...
Hi there,
I was wondering, do you have a generic "module on PCB" for Nrf9160? Much like ESP32. I would like to skip the design of the RF impedance maching... not my cup...
Hi,
I needed assistance to get the SKY66112-11 FEM working with the Radio Test Example, for certification testing (FCC, CE etc). I am using the NCS 1.5.1 SDK. I have followed...
Howdy ya'll,
I updated nRF Programmer yesterday (1.4.8 -> 1.4.9) and noticed binaries were not flashing to my board anymore. My JLINK is able to read the device's memory...
Hi, I am in need of some guidance. The overall goal is to set up MQTT/TLS communication from end devices in a thread network, via a border router to the AWS cloud. I have...
Hi. I am currently having a nrf52840 custom board and tried to program the sniffer hex file. nRF programmer gave me couldNotOpenDevice (0x4) Lowlevel error: JLINKARM_DLL_ERROR...
Hi all, I have a problem. I'm using a mix of the nrf samples azure_fota and azure_iot_hub connecting to Azure, using certificates X.509. The problem is the expiration date...
Hello everyone.
I have a nRF52840 DK that I am working with.
1.) When I plug into the USB port J2 (MCU interface) I am able to connect to the board program/debug using...
I wrote some code that has multiple custom services where my device acts as GATT Server.
I register the handler for every service (3 in total) with NRF_SDH_BLE_OBSERVER...
Hi,
I am debgging QSPI( type name: IS25LQ040B) in nRF52833, I met " NRFX_ERROR_TIMEOUT ", Could you give me some advice, please?
// Set QSPI pins to pins related to...
Using this \nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_blinky and nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_blinky_c
As described in \examples\ble_central...
Dear community,
I'm facing a problem during bluetooth scanning. I'm using the example named in the subject. This allows me to use the UART as debug printout.
I slightly...
Hi, I'm trying to upgrade nRF Connect SDK from 1.3.0-rc1 to 1.3.0 because I need one of the bugfixes to keep developing. I'm on macOS catalina and I've used the Toolchain...
