I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am looking at and testing the ble_app_hrs_c_pca10040_s132 example.
When the whitelist ist set up with the "whitelist request" we execute the following two lines...
Hi,
I am developing an application that requires communication between two nrf52840-based devices. There is a scenario in my application where the devices needs to exchange...
Hi,
[179] RTC: COMPARE event is generated twice from a single RTC compare match
This anomaly applies to IC Rev. Revision 2, build codes CKAA-Dx0, QIAA-Dx0.
It was...
Hi everyone, I'm an intermediate level nRF Connect SDK IDE programmer, and I describe my issue below:
1.- In the link below I found an example of code for the analog port...
The SDK version is using version 17 and I am using NRF52832.
I checked the following scope waveform for the next SPI communication.
Question
I want to remove the...
nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_ble\arm5_no_packs
Why the compiled hex file is different from before, and the code is not modified
I like to use nRF toolbox to monitor my glucose meter. To my understanding, after the glucose device connected with nRF toolbox, they will be exchanging data. So my question...
Hi,
When attaching external GPS Antenna to Nordic Thingy91, I realize that the power consumption increases by about 5mV. Are there any ways that I can config to unuse this...
I just solved this bug, so I'll share my solution.
Bug description: cannot run application after upload via nRF Connect v3.6.1 - Programmer using MCUboot. Upload is successful...
Hello,
I am ble to connect with nRF 52840 using pygatt bluetooth command.
sudo gatttool -b E5:3B:A6:E1:58:86 -I.
[LE]:connect
[LE]:Connection Successful.
Even...
Hi,
I'm using nRF5_SDK_17.0.2_d674dde\examples\peripheral\twi_master_with_twis_slave\pca10040\blank\ses to check I2C as per infocenter TWI testing document.
I have done...
Hello,
I've been using https://github.com/NordicSemiconductor/pc-nrfutil for few years now as a library of my own application to do DFU of a device. Everything worked and...
I am using an nRF52 DK and running a modified version of the heart rate collector example from the pc-ble-driver-py repository.
My modified program scans for connectable...
If you can expect the data to be sent or received at random times over UART, does it make sense to suspend the UART in the driver? Is it fine to leave both TX and RX enabled...
