Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I am using the NRF9160DK, I have already made all the getting started and compiled an example to use the LEDs on the board with em studio. I had already connected my card...
Hello,
I am trying to send some sensor information via thread / mqttsn every 5 min. Therefore. The dongle has to wake up (5 sec.), send the information and return to sleep...
Hi friend,
I used SDK16.0 and softdevice is S140. I modified ble_nus_c to a custom 128-bit UUID. It has 1 service (0x0211) and 3 characteristics (0x0212, 0x0213,0x0214)...
Hi,
I'm testing the aws-FreeRTOS code.
In detail, It's a BLE test
The problem is, BLE can connetc in the test but next step (read/write) cannot
BLE connect apple...
Would it be possible to illustrate what AT commands would be required to set up and send a UDP packet for the nRF9160, including configuring the modem, turning the modem on...
I'm writing a program that receives a time from an RTC over TWI then writes that time into flash memory using the example from the flash FDS library. The problem I'm running...
Hi,
Am using nrf51822 as central, i want to discover and to commuinicate with the service of another ble module (which is RN4871 from microship).
My problem here is that...
Hi,
I'm trying to flash the firmware to some custom built pcb's with NRF52840 on it. The first time I flash it, it works great.
Then, if I try to erase the chip (or any...
Hello
I have this firmware running in C:\Users\danie\ncs\v1.5.1\nrf\applications\tracker on the nRF9160-DK, nRF9160 SICA B1 is the marking on the chip
Modem FW is...
Hi. Some questions regarding the nRF9160 ENABLE pin:
1. According to the nRF9160 product specification the ENABLE pin voltage requirements are like this:
In the first...
Is it possible to add additional UI for different sensors in nrfcloud platform ? I could see that there is a predefined list of sensor types that can be attached to cloud...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK_v5.0. I would like to measure the time required to send a message from client to server...
Hi all,
I'm working on this example: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v3.2.0%2Fthread_example_dfu.html
I'm struggling on the server part, I...
Hello,
we are developing a verry small sensor node. Since we like to know if the sensor we are connected to, is one of our sensors instead of an attacker fake sensor we...
