Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I want to use a MPU6050 sensor with my nrf52832 board.
I connected the SDA and SCL pins of my sensor board with the pins P0.26 and P0.27 of my nrf52832 board, respectively...
Hello. I'm working with multilink example and I've got some problem. I want to send data to specific peer device, but after restart central or one of the peer, they reconnects...
Hi. I have a problem with Segger Embedded Studio. I always get more than 100% of RAM usage when building project on SES, even if examples projects from SDK . Anyone know what...
Hello, I have the following question. I'm trying to program my firmware via DFU Bootloader and nRF Connect (smartphone). That works perfectly with the test board SparkFun...
Hi,
I am using the two units talking with each other for the BLE uart.
One is running with the example ble_app_uart_c_central. The other is running with the ble_app_uart_peripheral...
Hi, After updating my nrfConnect to 3.6.1, I had issues using my J-link being unrecognized in the programmer app. The J-link I'm using is part of a Silicon Labs Dev Kit, checking...
Hi, I was wondering if there are any problems with connecting VDD to an external power supply when using nrf52840 in the high voltage mode? I would like to connect VDDH to...
Dears,
1.I want to know when working at USB CDC mode, what's the phy rate could be supported? And what's real rate is it？
2.Could customer customized their private protocol...
Hi,
I've read that highly secured IoT devices have a hardware root of trust. One very important feature of it is a private identity keys to prove identities for mutual authentication...
Hi,
I noticed at least using pwr_mgmt we are calling two times nrf_pwr_mgmt_run for every interrupts ! All interrupt seems to be triggered twice ! Or wakes from idle state...
HI Nordic
I currently have a 2 separate projects, that i'm trying to merge.
- Production test tool with RTT CLI interface on nRF52840 (Here I use JLink.exe -device NRF52840_XXAA...
Hi Nordic teams,
I'm developing the function of Mesh DFU. I've test the nrfutil tool locate on https://github.com/NordicSemiconductor/pc-nrfutil/tree/mesh_dfu , and it works...
Hi All,
I have designed one device using nRF52840 MCU and software SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
From Software end all features are implement and...
Hi Sir,
As check nwp_024_v1.6.pdf, it only shows the tape real information w/ below series.
nRF24
nRF51
nRF52
nRF8000
nRF9160
I don't find the information for...
Hi,
I have a SPI peripheral connected to the nRF960 DK. In order to access this correctly, I need to be able to write a byte to a specific address first and then read back...
