Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hi All,
I am using SDK17 for my application currently. To sense ping change I am using app_button function as below. Normally my port pin remains high and current consumption...
Hi,
I am working with a NRF52840 with the SDK16 and I am facing field issues with the peer manager flash usage. At each connection the app subscribes to characteristic and...
Hi,
I wonder there is not any TX_POWER_LEVEL macro used/defined in the source code of below peripheral application.
"examples\ble_peripheral\ble_app_hrs"
Does it...
Hello, sorry to bother once more.
I am new to the nRF world and bluetooth in general, I am trying to build a device /app that gets data from 3 sensors. 2 of which operate...
Hi all,
in order to put the whole project under a decent version control system I need a list of all files used in the example project in segger studio.
The c source files...
Hello! I have the following issue with my nRF52833 board: I am in the first stage of working with it and I wanted to try the simple blinky example.
However, since there...
Hello,
I'm beginner with Nordic nRF52 devices.
I'm working on a PCA10040 (2.1.0) dev kit and I would like to communicate through TWI interface.
Then I have installed...
Hi! I was defining NRFX_WDT_ENABLED in sdk_config.h, but found that apply_old_config.h was undefining it.
Even though I had WDT_ENABLED defined to zero, the test in apply_old_config...
Please, give me an advice. I need to measure the supply voltage and trigger an interrupt after the measurement. An END interrupt is triggered only once. It must be without...
What's the difference nrf_cloud_agps and AGPS using google SUPL data?
I'm not clear about this. README.rst doesn't explain about it.
Also, to use the nrf_cloud_agps, do...
Hi Devs,
I am facing a weird behavior with my application, where the TWI writes return NRF_ERROR_DRV_TWI_ERR_DNACK or NRF BUSY
If I ran the TWI writes from the main...
Hi Nordic,
Does SLM application support IPV6, if yes could you please point us to the AT command set which configures IPV6 and also point to us complete AT commands list...
hi ... we have done one customized board which has nRF52832 controller interfaced with WINC1500 wifi via spi communication inbuilt. I have worked with the nRF52 example program...
We need to generate MCK of more than 10 MHz to achieve I2S connection between Nordic NRF5340 and MAX9867.
However looking at the data sheet there in no configuration which...
