Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi , i would like to send some sensor data coming from SPI interface and then send it from one nrf52832dk onto another nrf52dk or a nrf52dongle and on the receiving end send...
I am currently using softdevice s140 v6.1.0 with my nrf52840 product, and I am occasionally running into a Softdevice Assert located at 0x000154A2 while the device is advertising...
Hi,
I have a wifi chip MTk7628 that communicates over a usb to ttl chip cp2104 to the NRF52832. I was able to cross compile the heart rate collector and burn the OpenWRT...
Hi Team,
Why the RX selectivity performance is different on -MHZ and +MHz?
As I know, Rx selectivity (or call adjacent channel rejection) performance shall be equal or...
Is there a simple way to have linux time up and running with minimum current consumption and good accuracy?
Preferably, some class with get_unix_time and set_unix_time...
hello Nordic
i am working with the nrf52840 , sdk 16.0, s140
i am using the peripheral ble_app_blinky example as a base
i added saadc and twi, (spi and uart will...
Dear supporters,
I am designing an antenna for the chipset NRF52832. After several experiments indoor and outdoor environment, we got some issues. Besides, We got the same...
When I call sd_ble_gatts_hvx() it returns 0x3400 and I'm not sure why. The error indicates the sum of these three errors:
NRF_ERROR_STK_BASE_NUM (0x3000) NRF_GATTS_ERR_BASE...
Dear Members,
I tried to include temperature into my ANT HRM receiver code,
but when I add components\drivers_nrf\nrf_soc_nosd
I got plenty of errors, what do I...
Hi,
Using 'nrf5_SDK_for_Mesh_v5.0.0_src' exampe project 'light_switch' developed for nrf52 Development Kit(pca10040). How to make the same project working on Thingy52(pca20020...
I am working on a project based on the ble_app_hrs_rscs_relay example project which I have largely extended with many additional services.
For example I am offering an additional...
Hi
I am working on nRF52832 , I want to store the data in NVMC . so I am trying to write the data blockwise , I saw the layout each page consists of Block 0-7 .To each block...
Hi everyone,
Is it possible to implement a USB device belonging to the Personal Healthcare class with the nordic nrf52840 DK?
NRF supports Personal Healthcare USB class...
Hi, I have written these 3 functions to erase/read and write. When I write any value from address 1 it gives following wrong output(0 1 2 3). But When I start address from...
