Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Dear Nordic Support team,
Currently I am in the process of adding the USBD_CDC_ACM driver code to our existing application following your usbd_ble_uart example. I can receive...
Hi，
Our customer is using nrf9160.There is a problem about powem_on circuit .
Attach is the schematic diagram:
Here VBAT is 4V,PW_ON is connecting to the nrf9160...
Hi,
I'm using nRF52810.
And i'm trying to measure battery level using saadc.
The problem is saadc result is not accuracy.
When battery voltage is 3.3v, saadc value...
Have a brand new Thingy 91, latest modem firmware and asset tracker firmware: thingy91_debug_ltem_2020-10-30_5522ca2b.hex.
But within the LTE monitor app, nothing shows...
For the nRF52811 there is only one TWI peripheral and if there are multiple buses required it is necessary to remap the SCL and SDA pins to the peripheral. In the nRF5 SDK...
I am migrating to the Fanstel BT840XE module with nRF52840 and a Skyworks PA/LNA. I need some assistance in getting my PA/LNA working in a multiprotocol setup.
I have successfully...
I have application developed that works ok on nRF52 DK (nRF52832) with S112 and now want to migrate it to a custom board with nRF52840.
Could you confirm that S113 is...
Hi:
Since we have a issue that when nRF52840 setting to DCDC mode, our inductive touch will have bigger noise, if setting to LDO mode, the inductive touch noise disappear...
Hi,
I've been trying any way I can think of to work around an issue "51" returned by nrfjprog executed from nrfutil when trying to run serwer from the steps in tutorial...
Hi experts
i am using nRF Sniffer to decrypt the BT Mesh packets with Wireshark, it can work smoothly. However, i tested and found that the packets device key encrypted...
Hello, I am looking at the mesh dfu example code on nRF mesh SDK-4.2.0 on an dk_nrf52840 and I have some questions.
Rather than having both a bootloader and main application...
Hello.
We are developing products using BLE modules.
The one used for that module was "nRF52832 (512kB Flash, 64kB RAM)".
I would like to know
Question 1:
As a...
hi ,
I am working on the nRF52832 , I am trying to store the values in structure and then passing over BLE . I am getting this error after print statement unknown function...
Hi,
I am trying to evaluate nRF5340 FOTA update via Bluetooth. I started with the Bluetooth/peripheral code sample as the basis for my project. I modified the project per...
Could you clarify the use of nrf_esb_set_retransmit_count function?
From what I understood, if it is 0 and it sends a message that wants to be acknowledge , it will not...
