Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Dear,
I am using NRF52840 and nRF5_SDK_17.0.0_9d13099 and SES development tool.
And also, I am testing SPI master with p0.29/30,31 and P0.26.
but when I do "nrf_drv_spi_init...
I am tring to DFU by Bluetooth with example, but it not work.
Please someone help me!!
My environment
PCA10056 nRF52840
SDK17.0.0
examples/dfu/secure_bootloader...
I was working with the Thingy:91 trying to get into into a serial printing state. I tried to updated the modem and firmware using the nrf Programmer. When updating the modem...
I've been having problems trying to get any of your example project to use NLOG to a uart port that we have made available for production test on our new product.
I've chosen...
Hi,
I am desperately trying to read some RTT Input with Zephyr, but I just cant get it to work!
All I want is to read the RTT Input. I tried with the console and the shell...
Hello,
I am looking at the nrf52840-dongle to explore Bluetooth audio (in headset mode).
So - just to double check:
(1)
I assume I can interface to bluetooth audio...
I'm using nRF52832 + SDK17.0.0 + s132_7.0.1. I am testing buttonless DFU on the PCA10040 board based on this blog, The initial DFU (when there is no app) is successful:
...
Hi, 1) I want to run the client-mesh from DK sources into Dongle. So, I did: - modified the client-dk project: nrf5_SDK_for_Mesh_v4.0.0_src\examples\light_switch_dongle\client...
Hi,
We have been working with a coordinator and a router device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
Hi Support-Team,
My iOS app crashed when I updated IOS-DFU-Library from V4.6.0 to V4.8.0.
I attached the Xcode debug info and iPhone Analytics.
Thank you very much!
Hello,
Would appreciate some understanding of a compiler warning. Developing for nRF52832 using SDK 15.3.0 plus S112.
This code compiles without warning:
Then I switch...
I have tried a lot of different settings but the NRF52810 still does not output carrier..
How do I configure the radio to only send carrier for NRF52810?
Hi,
I need to stream data from NUS UART Central Device to one peripheral, but the device always disconnects while trying to send second set of data. So I changed the write_req...
