Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I want to secure advertised packets using ccm
I am using s132 , SDK 14.2.0 and nrf52 dk
I found that AES-CCM peripheral is blocked by soft device usage and that I need...
I have this error.
In a last time with same error on a nRF52832 I decided this problem with increase:
On the 52832 it works. But on the 52810- project fall.
How to...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
As part of ble_evt_handler...
Hello All,
I am developing a custom board with nRF52832. All good with Segger Embedded Studio, I could download and debug the board successfully.
When I tryed to program...
Hi, i'm using nRF52840
I'm using 2 uarts :
one (uart0) is only for logging and another one (uart1) is for communication.
I can send from both uart, i can see i receive...
Hi
I sometimes get stuck in the zb_nrf52840_abort but the stack trace seams to be strange, its only containing two levels, Am I missing something or is there a better way...
Hello,
I have inherited a Thingy:52 project which was using some old versions of SDKs. Now I am trying to port it to a newer version in order to make it compatible with...
In nRF5_SDK_15.3.0 some undefined reference error reported when using nrf_drv_clock module (example: undefined reference to `nrf_drv_clock_hfclk_release)
The problem is...
Hi,
Is it possible to update the modem firmware once the product is on the field? I'm not talking about the application hosted on the M33, but the actual modem firmware...
Hi,
I'm testing pca10059 usb dongle with pc-ble-driver (not nrf-connect-pc)
I need 2M phy because of throughput.
latest pc-ble-driver support nrf52840 with softdevice...
HI,
i'm using SDK 15.2.0 and MESH SDK 3.1.0.
my program using the uart to get data from a sensor and sending it over the mesh network.
now i'm trying to write to the...
Hi.
I'm using
An nRF52832 DK
SDK 15.3.0
Segger IDE
The soft device is S112
JLinkRTTViewer for debug
I'm using the ble_app_proximity as my starting point and...
Hi Nordic;
I am using ble_app_uart_c example to scan data with BLE_GAP_EVT_ADV_REPORT. So now i have to send this information to Arduino Uno how it would be possible?
...
Dear all,
I need to read out the voltage of the battery that supplies my nrf52. From what I have read I see that there are 2 options: LPCOMP and ADC.
Due to restrictions...
