Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
I am using Seeger for Flashing code and Debugging. I ported code from “flash_fstorage” example code to “ble_app_blinky”. I have few queries on write data into Flash...
Hello,
I am trying to configure Pin P0.09 as SCL pin for TWI. But I am not getting any results with this pin while I get data when any other GPIO pins are configured as...
SDK: 15.2.0
SoftDevice: s140 6.1.0
Hello,
I seem to keep finding conflicting information on how the NRF52 manages power to its peripheral devices and whether the application...
Dear proffesionals,
I am very beginer to nordic chip.i am using nrf_SDK_15.0.0_a53641a version.i am trying to integrate the writable_ndef_msg file to bluetooth.so how to...
Hello,
I am using custom hardware with an nRF52810 chip, connecting it to P16 connector of the power profiler kit. I use the power profile kit to check power consumption...
Hi guys,
I am a newbie in nRF but with some experiences in embedded systems . I have just been asked to work on a project that connects a nRF52811 to a nRF91.
I initially...
I'm testing a gps sample program below. github.com/.../gps
I have two questions about it.
1. It doesn't acquire NMEA data. it always stops working when it reaches 30 sec...
Hi
I tried to connect my dongle to PC but it is not getting detected , Even the red LED is not blinking., Can someone help me out with this issue
Thanks
Tabassum
I'm using LPCOMP to sense multiple input.
I call the lpcomp_read() function below for each input pin.
If I only call this function for 1 pin only, it worked fine.
For...
Hi,
I'm developing an application requiring multiple connections to several peripherals from a single central. I followed the instructions given here https://devzone.nordicsemi...
Does anybody know a quick and easy way to disable the radio functions in a soft-device application?
I want to measure and optimise the power consumption of all the other...
Hi
Can someone suggest me how can i erase the secure bootloader from nrf52840(Dongle),Because am unable to get "erase all" or "erase and write" option in nrf connect application...
Dear Nordic Team,
I can not flash my nRF52840 USB dongle with the nRF Connect Programmer application.
The window looks like this:
Erase / Read / Write functions...
Hi,
I am wondering how connection and scan interval work together when using multilink central device. I am starting scanning (scan interval and window 0x80) again after...
So, after using my Devkit and everything working OK as far as I can tell, I decided to order up a bare BT832XE module and place it on my PCB.
Flashed it with the same firmware...
