Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hello,
I use the LAIRD module BL652 with an nRF52832 with the SoftDevice 14.0.0 (old version…).
The application use the BLE with the SoftDevice.
We have mesured the...
Hello,
Here i are using nRF52832 ,softdevice S132 and mesh sdk v3.0.0
For my Application,i need to go with DFU.so i merged my application into the example code of DFU...
Hello,
Does anyone know if the FreeRTOS port that's distributed with the nRF5_SDK_14.2.0 is intended to support nRF52810 chips (which have no hardware FPU)? I started working...
SDK 14.2 keil5
I want to run freertos with nrf52810.but I did not find any example .
Is there anyone have tried this?
I downloaded nrf52832 code(ble_app_hrs_freertos...
Hello All,
I have looked around for answers to my specific issue, however I did not seem to find one that aided me enough to fix my issue.
I have created a BLE profile...
Hello,
SDK 15.2, SD 6.1.0 with PCA10056 1.0.0, 2018.20. nRF Connect App v4.22.3. Pixel XL.
I'm running into an issue with my application where the phone disconnects after...
Using: Linux (Ubuntu 18.04), gcc/Eclipse, nrf52840, v15.3.0 SDK, SD 6.1.1
It has been a real bear of time using the SDFU in the newest version of the SDK. There were a lot...
Dear support,
Our team is considered doing their own smart watch, so i found that nRF52 chip is a nice solution. Just before we start, i would like to do some basic questions...
When we ported our FreeRTOS based project to SDK 15.3 from 15.2, we noticed a big jump in the CPU Usage. It turned out that the issue was in SDK 15.3's freertos port_cmsis_systick...
Hi nordic,
I send multiple bytes but always only receive packets of length = 1. For example in the picture, I sent 2 bytes 0x68, 0x69 ('DE') but only received the first...
Hi
What is the difference between ble_nus.c and ble_nus_c.c?
because i went through both the files and i felt both files are almost same except an extra function(db_discovery...
Hello, I bought a nRF52832 Breakout Board from SparkFun. from their tutorial, you can program this board using the serial bootloader and the Arduino IDE. However, aside for...
