i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hello,
I have SDK v15 and there is not much information in infocenter also about these two functions related to my doubt.
( NRF_PWR_MGMT_SHUTDOWN_GOTO_SYSOFF & nrf_pwr_mgmt_run...
Hello, I'm starting evaluation of the Mesh Light Switch Demo both on DK PCA10056 and on Dongles PCA10059. I 'm using SEGGER IDE and made sure to properly set target in Preprocessor...
Hi , i tried to modify the template example from the sdk 15.3 but im getting an compilation error from " nrf_log_backend_rtt.c"
SEGGER_RTT_Conf.h: No such file or directory...
Trying to up load mqtt_simple sample, however getting bus fault on terminal. have browsed after the same issue here, but don't work after doing git pull ect...
here's...
How to correctly reinitialize the BLE stack when using FreeRTOS?
I can not find in the libraries where the task for the work of the stack under FreeRTOS is created.
Stopping...
We have a connection between our nRF52832 (server) and a tablet (client). We're trying to transmit some data at a rather high throughput. The connection parameters are as...
Hi everyone,
I have a problem with my custom nRF52832 hardware. I soldered my prototype hardware and then I checked if it is correct by checking debugger SW device settings...
Hello,
I'm trying to get as much throughput as possible using the Coded PHY. I noticed that apparently the Data Length Extension feature is not supported together with the...
Sometimes, i found that my firmware still at the old version after update complete, there is no any error.It same happen on use Android-nRF-Toolbox to update firmware.
code...
Hi, I am interfacing external memory chip that is based on SPI protocol with nrf51822. I have to read more than 255 byte via spi in single buffer with 4 byte of command. Even...
Hello,
I am using a custom board with nrf52840 using SDK 15.3 and ICM 20948. I see a lot of twi drivers and its confusing which one to use. I want to read the ICM 20948...
I am using a Windows machine and would like to compile a sample nrf5* project (preferrably nrf52) by using the command line only - no GUI.
Can you please tell me how I might...
currently i set the GENERIC_ONOFF_SET_MAXLEN to 10 and from server i can see the message is received, not one package, but 6-8 packages from client,
my question is what...
I downloaded the nRF Connect SDK v0.4.0-rc1 by following instructions from the Getting Started Assistant, but I am unable to set in up in SES.
I tried to set the environment...
