Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I tried searching for this response but cant find exact answer
SDK15.2 and API6.1
I am trying to have an advertiser but would like to put it in some sleep mode and advertise...
There are a few pins I want to use but are already assigned to MCU interface UART or buttons like p0.05 to p0.08 and p0.11 to p0.16 on the nRF52840 DK. I’m wondering if it...
Hi,
We are encountering a problem when we try to avail Nordic UART service (NUS) and Mesh service in one application. The problem statement is that after Provisioning, when...
Dear Team,
We are working on nRF52832 BLE MCU. SDK version = 15.0.0. SOFTDEVICE version = 6.0.0. IDE = segger embedded studio.
In our application we required software...
Hi,
I have read this thread Notification_Loss but could not understand my problem.
On peripheral side, I am making sure that error events are properly handled while doing...
Hi,
I'm working on an application for the nRF9160 using the nRF Connect SDK. I want to integrate this app into our build system and thus would like to be able to build...
Hi,
we have to stick to SDK 14.2 because our project is close to finish and we use C++ which is not good supported be SDK <15 due to the macros.
But still we would like...
Hello, I am trying to adapt open thread coap example to use with the PCA10059/NRF52840 Dongle board. I am using segger IDE. I adapted the CLI to use the USB like in the thread_cli_usb_bootloader...
Hi all,
i want to read the power (WATTS) value and send it to ble. i have attached datasheet also. i want to know how to trasmit COMMAND e.g 0x58 through UART. any api...
SDK 15.2 SD API 6.1 SES I am trying to get my system to work on a DFU system. In order to do it i need to have a secure bootloader.
using the secure bootloader in the example...
Is there a way to configure the nRF51822 to support writewithoutResponse? I'm using the Adafruit Feather 32u4 with the nRF51822 ble chip. My iOS app works fine with the older...
Hi
I plan to use nRF52832 based nodes with an accelerometer sensor which generates data at a rate of 468 bytes per second. For evaluation, I have two nRF-52 DK evaluation...
1. I read the Configuring DFU over Mesh & nrfutil User Guide , but still do not know how to test this example.
2.is we must need 2 devices, A connenct to PC for nrfutil...
hi ,everyone
HOW TO do a DFU by myself serial protocol in mesh network ?
0.I know it can scucess through a python script in PC (even thougth i try failed to run this example...
Hello,
I want to develop a ANT+ product, example rope skipping or Dumbbell, but i can not find out these ANT+ Device Profile.
How can i do? Can i use a personal ANT+ Protocol...
