Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
After turning on the power,
I did not connect anything on the board.
but it is about 2.7 volts out of the pin (p0.04).
It was almost zero volts before,
but the output...
In my design the nRF52 is connected to an STM32 host MCU. I connected the UART for data communication and the SWD and RESET pins for programming.
The nRF52 needs to be programmed...
Development Software:
nRF5 SDK v15.2.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware:
nRF52840...
Hello ! I encountered a problem in sending and receiving data from one nrf51 card to another nrf52 card
i use this method in (ble_config.c) to send string data :
void...
Hi everyone,
I am developing a quick evaluation demo for a low-power sensor node which consists of the following steps:
- read a couple of GPIOs
- set advertising...
Hi, we are developing an application using USB with NRF52840. We want to connect to the PMID of our battery charger, which will have either USB voltage or battery voltage...
We are using nRF52832 on original PCB board.
We are trying ADC at single-end input, 10 bit resolution, reference voltage is internal 0.6, gain is 3.
We are using regulator...
I would like to update my advertising data on the fly but actually it doesn't work. Many many posts talk about this behaviour, but no working answers .
Before SDK15, we...
Hello there!
My project use comparator, timer capture and pwm to measure capacity of line.
The purpose is to encounter open circuit condition. So this does not require...
I'm trying to use an iPhone as gateway for nrf Cloud. The user is "Verified" and the "Gateway Name" is the same in the app as the only gateway I have in the nrf Cloud. But...
Hello all,
We check the custom board with nrf52840(BL654) , but it's hang PC and devices when connect the PC.
When the hang on my pc , we checked windows system event...
I'm using SDK 15.0.0 on nRF52832_xxaa.
I'm currently using RTC1 as a low frequency timer to keep track of time elapsed while my device is sleeping. This works well and I...
Hi,
I modified the UART example to work on different pins i.e. pin 17 and 15 on custom board. When I use printf() to print logs, it works. If I use the NRF LOG to print...
Hello,
I am trying to build a small voltage stimulating probe for a research project I am doing. I was going to originally use the Rigado BMD-350 which includes the nRF52832...
Hello,
I am trying to connect my nRF52 DK to my phone (apologies not desktop) and perform a DFU OTA via the nRF Connect app. I'm using SD132 6.1.1, and uploaded the secure...
