Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I need to send the following sequence of bits through TWI
start bit | 7 bit address | write | slave ACK | stop bit
I looked through the twi_hw_master.c and it seems...
When building a project that compiles the hal_nfc_t2t.c, it errors for nRF52840, but works for nRF52832.
For the nRF52840, I get these errors:
Looking for some of the...
Hello, I want to transfer a large file (approx. 1.5MB) over BLE using nRF52 Module in a way where BLE Host and BLE Controller will be on the nRF52 SoC and the application...
I added ams service to my project, and I tested with my iphone 7P, seems all goes well. But today I tested with my iphone 5S, sometimes the hardfault exception raise.
Hi Nordic,
I'm trying to use a nrf52832 dev kit (v1.1.1) with NRF Connect (v2.5.0 on mac) to communicate to my device (NRF52832). My device has implemented MTU exchange...
Is there something on the specifications regarding the structure of a node? We have a node currently with 3 Elements:
El0: Light controller: Config model, Health model,...
Dear Sir,
I am using SDK15. Softdevice s 132, and nrf52832.
I was working with code 'ble_app_template'.
I was trying to find out the transmit power set for the...
I am trying to create a datalogger onto a uSD card with a fat file system. I have been able to run the fatfs example which creates a file on the uSD card, NORDIC.TXT. The...
Hello
We have a double problem, the CPU wake up doesn't work, but the sensor who wake up the CPU is correctly configured ant the interrupt pin go low to high when the temperature...
Hi Sir
We plan to implement our own DFU controller on host MCU to upgrade on board DFU module by UART.
Zip file will be generated by nrfutil and saved on flash.
Can...
Hi,
We've developed a BLE HID device with mouse and keyboard capabilities based on the nRF52832 and SDK 14.0.
We're interested in declaring the CoD as " Combo keyboard...
SDK : nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac
segger studio
I merged uart peripheral into simple coap clinet example
this is errors:
Output/Release/Exe/thread_simple_coap_client_pca10056...
I have the USB Dongle (PCA10059) which after a full erase, has been giving only 1.8Volts to the GPIOs and the VDD OUT pin.
I am using the Segger j-link EDU progammer/debugger...
Hello Community,
I am looking for some assistance in getting my nrf9160 DK to connect.
I am running the AT_Client sample and LTE Link Monitor. I am in Toronto, Ontario...
