I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I have project based on nRF52840 (using SDK 15.2) and I have a problem with properly adding ADC measurement using scheduler - description as below.
Problem description...
Hi
I want to create this example:
A major network,it include the subnet A and subnet B.
One node X,it belong to subnet A and subnet B.
If the node X was a function...
Hi
We currently working on nrf52 dk with SDK15.0.0 but we will use nrf52810 rather than nrf52832 due to cost.
As I know, nrf52810 doesn't have FPU compared to nrf52832...
Hi,
I am using nrf52832AA, SDK15.0, SD s131.
In some cases, an NRF_DRV_TWI_EVT_ADDRESS_NACK event occurs during I2C communication with the IQS263 sensor.
It would be...
Hello,
We have a custom board using the Rigado BMD340. I have uploaded the usbd_cdc_acm example code onto it. Everytime I plug in the USB, my computer fails to recognize...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor...
in my application i have to read the ADC (single channel) each 30us within 3 ms. And there must be no interruptions in this period of time. Then i can let radio up to 3ms...
Hello, I am receiving the error below when trying to build an application using the command:
C:\Nordic\ncs\nrf\applications\asset_tracker\build>cmake -GNinja -DBOARD=nrf9160_pca10090...
hi, I have nRF9160 SIP based custom boards.
I received GPS firmware from FAE.
We have our bias and antenna can be connected to our custom boards but can't connected to...
Hi, I am trying to add numeric comparison function to the project nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\app_ble_uart\pca10028\s130. in the project, there is no support...
Hi
I am working on ble_app_cli to acieve my requirements.
I want to whitelist device based on recieved scan request report before making connection with the central. ...
Hi everyone,
I'm working on the nRF52810 to let it comminucate with an ESP32.
The ESP32 is a client so I run a server on the nRF52810.
First the client starts scanning...
