Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello!
I use the NRF51228 board like this PICTURE
The ICs revision QFAAH0.
I use Keil-uVision 5.17 and ST-Link V2 from STM32F4 Discovery board to load firmware HEX as...
Hello,
I am just getting started with my nRF52832 and went through the first getting started tutorial . I use the SDK V11 with Keil and Termite as described and an iPad...
Hello,
I run ble_peripheral\ble_app_uart example from this link : devzone.nordicsemi.com/.../36
Used PCA10040, SDK 11, S132 2.0.0
I use Termite3.2 and IOS nRF toolbox...
Hello, I am toggling two separate pins at different rates but it looks like for whatever reason the when I go to clear one gpio register it clears everything. I understand...
Hello,
I would like to make use of white list advertisment for my heart rate application on my nrf52832 s132 pca10040, currently I am using SDK12.2, is there some example...
Hello,
I used translation software.
I'm looking into LDO mode and DC-DC mode.
However, I did not know what LDO mode and DC-DC mode are.
What are LDO mode and DC...
I'm working on a project that will utilize the nRF52832 as the Host and Controller and an STM32F3 as the application using serialization.
I've included the nRF5 SDK V14...
We just produced a PCB with a NRF51822-QFAB-R7, does Nordic provide a EMC test firmware that we can flash onto the chip? Basically need it be always transmitting....
Thanks...
I'm using the original BLE App UART from nRF5_SDK_14.0.0 on a PCA10056 Board.
The board is advertising, but if I want to open a BLE peer-to-peer connection, than the application...
With SDK 14.0.0 and Softdevice 5.0.0 I have problem with Windows 10 connection. The device connects to PC but then almost immediately disconnects with reason 0x13 (BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION...
Hello,
We developed a few devices using the nRF51822 and noticed that the receiving range is reduced significantly from our nRF24L01 devices. The transmission range is good...
Hello,
I'm trying to measure the current profile with the PPK (HW Rev:1.1.0, SW: 1.1.0) but I see a lot of strange behaviors.
My firmware initializes everything and the...
I am running a nrf52840 dev board as an NCP connected to a RASPBERRY Pi running wpantund.
I have 10 other nrf52840 devices in the network. The PI has LIBCOAP coap-client...
