Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I've run into a problem with an OS API call when running FreeRTOS on an NRF51 due to how ticks are corrected.
vTaskStepTick() is getting called while the MCU is awake and...
Hello all,
I am trying to activate ADC to measure a voltage every few seconds using nrf51822. When it is done, I supposedly deactivate ADC so it does not consumes while...
I am designing an device and i need to communicate with the device using the I2C of my nrf52.
when ever i try to initiate the transfer process using the driver function...
Is there a Peripheral Encryption Example for the nRF52? and can the Master Control Panel tool(3.10.0.14) be used to test the Peripheral Encryption?
If i clcik the down arrow...
Question about usage. I am using the nRF52, and ported product code that was running on the Alpha SDK11 to the release SDK11. I believe that what I will describe is a new...
According to the product specification of the nRF51422 the current between the advertisements is:
i_sleep = I_on + I_rtc + I_x32k
16k Ram enabled: = 2,6 µA + 0,1 µA...
I realize that this code is "experimental", but we are trying to utilize it as a reference and having problems with its stability and scan results.
Specifically, we are...
Hi!
We are currently implementing a time synchronization algorithm using a nRF52s. Currently, we´re getting the min error of 20ms between synchronized slaves. We think that...
I'm using a nRF51 with 32K RAM and SD120. When I started using RTT Viewer I could send data to the terminal, and debug my code. Recently my J-Link plus won't allow me to debug...
I'm trying to secure my peripheral by allowing only bonded devices to connect. I'm using device manager, when I bond a central with nrf master control, the bonding succeed...
Hi,
I'm facing the following issue when trying to use the DFU bootloader. Below you can find the code of the bootloader, which I flash after I erase everything, flash S110...
hii....
i want to make my device connected through a secret pass code (may be six digit)..ie. my device get advertise then when master control panel discover my device...
Hello,
I was just wondering what are the steps to download my software that I made to nRF51422 to the nRF51822. I changed the target device and the memory areas in the...
Hi,
I am using SD 120 9.1.0 and SDK 8 as a central and SD 110 V8.0.0 and SDK 8 as a peripheral.
I have a setup central connects with 8 peripherals. First I had 1 central...
Hi guys,
I'm wondering what is written there in "empty section" between 0x7c0 and 0x1000 address? Are there any special registers (which must not be overwritten)? It looks...
