We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I want to make nrf51822 with accelerometer.But Keil compiler dont know.What I do?
It was given as examples of programs I want to do. devzone.nordicsemi.com/.../.I
I want...
Hello Guys,
I want to go with nordic solution for the bluetooth low energy application. Can anyone please explain me how much it will cost to develop your own module including...
hiii....
i am developing a custom profile with five services... i want to make these 5 services and its characteristics available only for some authorized devices.. ie...
I am working on a custom service using and nrf51822 device. SDK7.1 SD7.1
My security parameters are as follows:
#define SEC_PARAM_TIMEOUT 30 /**< Timeout for Pairing...
Hello,
I am running the UART app example in SDK 0.9.1 with the nRF52 and PCA 10036. I am using putty to send and receive messages, as well as the nRF UART v2.0 app for...
Hi,
I'm currently trying to determine the power consumption of my nrf51DK during different states of my program using an oscilloscope. To do so, I am using an external power...
We had been trying to use SD 7.0 with SDK 6.1.0, but realized our libraries were mixed up and not controlled very well, and we were experiencing occasional crashes where the...
Hello,
I'm looking to find a way to send a 32 bits number to the ledButtonDemo with the Master Control Panel (I have the Nordic dongle).
Indeed, I replace uint8_t led_state...
Hi,
I have a question regarding the NRF 52 boot sequence.
When we first receive it from Nordic, what are the boot options? Are there any other options to load a code on...
Hi,
I'd like to know how to set/alter passcode when pairing happens. I looked a few examples in Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Examples\8.0.0\ble_peripheral but...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hi all,
If i have connect a band with my phone, then i let my band close to my notebook and let my notebook unlock.
Any suggestion about this?
Thanks in advance
Hello all,
I am working on the implementation of DFU OTA in our application, running on a custom board using the nRF51822-QFAC.
The tools that I am using are:
...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
[Update 8/15]
Here's the file for the main part of my code: sensors.c . The sensors_start() function at the bottom is where the while loop and the print statements are located...
