Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hey everyone,
I am having trouble setting up the lsm6dsv16x as a interrupt. I was able to successfully poll the data meaning I can talk and read imu data, but no interrupt...
Hi , I wanna keep my existing mobile application which talks to nRF5340 over the BLE NUS service. I am using the default BT_UUID_NUS_VAL as my primary mode of communication...
I want to edit the explom firmware that comes with thingy91 to add the reading of new sensors and send them to nrf cloud. Where can I get the example of the Asset Tracker...
I have a custom board that started life based off of RF9160-DK 1.1.0.
We have a single programming header that can be used to program either the 52840 or the 9160 depending...
I've installed nRF Connect for VS Code Extension Pack v2024.9.5 to ubuntu 22.04 and after opening vscode the free disk space continues to diminish and cpu load is constantly...
Hello,
We are working on an integration between a nRF52832 and ST LIS3DH accelerometer on our custom board, using SDK 15.2.0 with SoftDevice and BLE enabled, and have observed...
The last couple of months I have been following the course “nRF Connect SDK Fundamentals”, but I am unable to get further than Exercise 2. This is because Visual Studio cannot...
Hello,
I’m having issues with time synchronization when using the sidewalk Sub-GHz template from SDK v2.5.0. My setup includes a Nordic Semiconductor chip nrf52840 and LR1110...
What is the reason for the default 320 hour setting for periodic Tau timer? This seems like an awfully long time, and we're wondering if this is simply a placeholder, or if...
Hi. I'm finally bought a PPK2 to test some of self-built IoT devices. I do have a question in regard to the device (before I break anything). Does it offer any types of short...
Hi. I tried using the TWI master and slave drivers on 2 different nRF52840DK boards. The 100KHz frequency is perhaps a little high and I will see how to lower it by acting...
HI ALL,
I want to create a static library in the application layer, but this library will contain nrf related header files, which will cause cmake to not compile properly...
We have a custom board based on the nRF52805 and we're seeing some odd behaviors in debugging / testing that we're trying to nail down. Two questions:
The INFO.VARIANT...
When I use the J-link programming program, the following happens to the J-flash connection chip
SEGGER J-Link Commander V7.67d (Compiled Jul 5 2022 16:15:35) DLL version...
Hello, my custom board is using pin 09 to communicate through uart. I want to check that uart is working on this custom board. First, I tried to create a simple uart application...
