Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am using the nRF52840DK with nRFConnect for VS Code. In Lesson 6 Exercise 1, I connected the DK to a BME280 board I purchased online. The board exposes the four pins needed...
I've been wrestling with an issue whereby I attempt to deploy an mcuboot image to a device and inconsistently I get a message that says the firmware image is not valid (error...
I am currently encountering an issue with BLE bonding logic in my application.
When a phone initiates a pairing request and triggers a pairing pop-up, I use the security_changed...
We have a custom PCB with a nRF9151 implementation supporting both LTE/NB-IoT and GNSS. The PCB has no switching regulators or any other possible noise source except for the...
Working the SDK intermediate course, L1.E1. (SDK 3.2.1 / nRF54LM20A)
After building, I select <Debug> under Actions in VS Code. I get this popup that says "Debug options...
Hi DevZone Community,
I am facing a build issue while working with the following environment:
Environment
SDK: nRF Connect SDK v1.9.1
Hardware: nRF9160 DK...
Hi,
As the subject states.
I would like to run the tests at zephyr/tests/drivers/spi/spi_controller_peripheral as intended in testcase.yml. I can verify that I have the...
Hi All,
Anyone has experience in FRAM?
I have a project which need to integrate the FRAM CY15B108QN with nRF52840. I got a weird result by using nRF silicone, but can...
Hi,
I wanted to use the `nordic-semiconductor.nrf-kconfig` and the `nordic-semiconductor.nrf-devicetree` without the nRF Connect extension in `vscode`, but they don't seem...
Hello, I am an absolute beginner with nRF9160. I have just received one development kit.
I am trying the Quick Start application for cellular modem with AT commands.
Unfortunately...
Dear Nordic
At ncs3.2.0 zephyr sample, we found uvc sample as below.
https://docs.nordicsemi.com/bundle/ncs-3.2.0/page/zephyr/samples/subsys/usb/uvc/README.html#uvc
...
I am currently trying to get hello nRF Cloud example running. However, my Thingy:91X doesn't connect with the nRF Cloud. According to the logs of the cellular monitor application...
If the BLE_GAP_ADV_FLAG_LE_GENERAL_DISC_MODE is not set successfully in the broadcast settings, it will result in an error of NRF_ERROR_INVALID_FLAGS when calling sd_ble_gap_adv_data_set...
