Hello!
We are planning to purchase an electronic component nrf52840 and produce a finished product on it.
question
1. Will it work immediately on the ZIGBEE 3.0...
Good morning, I have a question about NRF Util. I need to make some changes in souce code of nrfutil for my own needs, but the most recent version, which is provided on Github...
Hi. I interested now for direction finding in nrf52 series. I have nrf52811, nrf52833 and other controllers. But i don't find any information how develop board for recievers...
Zephyr Eddystone example is connectable after power on of nrf52833 board. But after disconnect it becomes non connectable. How to fix it? And how to change advertisement interval...
We are looking for an experienced software developer, for existing board with using nRF Connect SDK. We are using nRF52840-dk.
Please, contact me if you are interested.
Hello,
In nrf_dfu_ble.c BLE_GAP_EVT_SEC_PARAMS_REQUEST pairing on Windows 10, the following code:
err_code = sd_ble_gatts_value_get(m_conn_handle, BLE_UUID_GATT_CHARACTERISTIC_SERVICE_CHANGED...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
I want to implement the function of periodic temperature collection，but I didn`t find any data show in putty terminal，and I`ve set NRFX_TIMER_ENABLED 1 NRFX_TIMER0_ENABLED...
Hello,
The BLE mesh spec says the following:
Heartbeat is used to monitor nodes on a network and discover how far nodes are apart from each other.
Is there an example...
Hello. I have read a topic about ADC calibration (gain and offset error in 0x10000024) of nRF51822 here but I can't find the document describing it. Could anyone point me...
Hi,
I am beginning to design a wearable device with motor vibration using nRF52 SDK and SoftDevice S132.
In firmware side, I have no problem to control a led on and off...
Hi
in my test bench for system validation I would like to control the system based on nRF52 via Bluetooth to speed up testting of various samples.
It seems that there...
Good day.
We recently bought the NRF52 DK and the Power Profiler Kit with the intent to log power consumption of our battery powered products. Before purchasing the products...
Hi,
I tried nrf connect and nrf hrs example. I used nrf52DK. I bonded the device, and connected with autoconnect. I turned off the nrf 52 DK, and turn on. The nrf connect...
I am using the secure bootloader with DFU, and the buttonless DFU service. I extracted these applications from the Thingy SDK v2.1.0. This works perfectly fine as long as...
Hi,
My problems are as follows:
SDK :nRF5_SDK_15.0.0_a53641a.
IDE:MDK 5.2.6
Chip:nrf52832 SPI0
External Flash :W25Q64
Now ,I can read the chip ID correctly ,but...
Hi,
Please find following source code.
After compiler by Keil 5.24.2, some code will not compiled,
I can see the situation by "enter debug mode, please find following...
Hi,
I am trying to develop a central device that would scan for devices that start with a prefix XYZ_, for example XYZ_1111, XYZ_1245,...
Is there some way to add a name...
Hi,
I am using esb function to implement my project, and I set "noack" condition to "true".
How can I know the destination address when I receive a packet?
Thank you...
I need to add ARM_MATH_CM4 to my preprocessor definitions using Segger Embedded Studio.
I know this has been dealt with in "nRF52832: How to Include the "arm_math.h" library...
