I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I refer to https://github.com/alc6/nrf52-pc10040-multiperipheral-passkey/blob/master/main.c for implementing static passkey. But pm_sec_params_set() returns errCode=0x7. ...
What I've done
1) Set up ot-br on an Rpi4 by following this guide .
2) Set up a 52840Dongle (plugged into the RPi4) as RCP by following this guide .
3) Installed the...
I'm using SDK 14.2.0.
I'm trying to read the device ID register from ISM330DHCX accelerometer this way:
ret = nrf_drv_spi_transfer(&m_spi[Instance], ®_addr, 1, read_temp...
Hi guys,
So lately, I decided to update the sdk from 4.1.0 to 4.2.0 and there are some problem that I can not solve myself. So I use the macro ZB_ZCL_REGISTER_DEVICE_CB...
Hello,
i've trying to update the codebase of our current project (under development) from NCS 1.9.x to NCS 2.0.x.
I'm experiencing hard fault crashes when I try to perform...
Hello,
I'm using SDK 17.0.2 with S113, v7.2.0 on the NRF52840. We currently have an instance of CLI running in our executive loop, and it works fine. We'd also like to implement...
I facing the above issue when build a project. The project structure is below. I copied the Git project project to d:can/firmware/zephyr/samples/drivers/can from https://github...
Good day Nordic people, I am facing a problem when erasing or writing to internal flash memory after enabling softdevice. here the details and tests: Setup: - GCC, arm toolchain...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi Support team,
nrf5 sdk for mesh 5.0, nrf5 sdk 17.0.2, s132, SES;
We are trying to understand the LPN feature based on the LPN example because in our scenario there...
We're developing firmware for a custom board that uses the NRF5340. Today one of the developers reported that they were no longer able to communicate with the board over SWD...
Hello, all
I built CLI sample for Openthread, but failed to run, windows 10 couldn't find any nrf52840dongle inserted, and not any log output through RTT.
When I debugged...
Hi guys,
i'm using DFU over serial and i get the error 4 in NRF_DRV_UART_EVT_ERROR.
This was not happening before and suddenly started.
What could be the issue?...
