I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
This is a followup question regarding this old thread I started: https://devzone.nordicsemi.com/f/nordic-q-a/48295/hold-output-pin-during-bootloader-jump
IC: NRF52840...
Hi,
I'm relatively new to your product line, but have been spending a bit of time trying to bring the volume control functionality into a SDK16/PCA10056/s140 configuration...
Hi,
I am using SD calls to start an advertisement of BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED :
sd_ble_gap_adv_start(m_adv_handle, APP_BLE_CONN_CFG_TAG...
Hello, I have a project that's fairly mature and working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a million...
Hi
I plan to use nrf52 DK to program my device by using a connector https://www.tag-connect.com/product/tc2030-idc-nl
But should I connect it to debug in or debug out...
Hello,
background: using Keil IDE, my own board that has a nRF52840 on it. My goal is to create automatic DMA transfers from SPIM3 peripheral.
I am setting up EasyDMA...
I'm porting a working app from SDK 1.1 to 1.2, and have noted that when I make an mqtt connection close it, and re-open (to a different mqtt server) that the call to nrf_connect...
I have reviewed most (if not all) posts on this forum that relate to multiple vendor specific UUIDs but still see issues on my platform.
I am using nRF52832 (with minor...
Working with nRF9160 running west build -b nrf9160_pca10090ns. I get an error FATAL ERROR: command exited with status 1: /home/ahmed/anaconda3/bin/cmake -B/home/ahmed/nrf9160...
Hello,
I tried to implement my own "Vendor model" by ( Documentation ) given. I am using example code from documentation. Using mobile app (nRF Mesh) I type optocode of...
To the kind attention of Nordic support team,
I'm interested in a ble example (SDK15.2 nRF52840 nRF52832) where peripheral device is waken up from being in deep sleep mode...
Hi,
I am working on the client program to retrieve the value from 4 characteristics at the same time using notifications. I have already done with the server program. Using...
Hi
I am trying to use the serial library with IRQ and callback function, but the event NRF_SERIAL_EVENT_RX_DATA is never triggered. No other event than NRF_SERIAL_EVENT_TX_DONE...
Hi support,
I'm currently using pca10040 on my custom board and want to be able to implement the CLI over uart port. My SDK is 15.2.
To get started, I test my board's...
I'm trying to inject the time when the advertising packet is sent to the central BLE module, but I'm struggling to add "sending time" data into the advertising_data_set function...
