I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
We wanted to use the NRF51-DK to flash a few nRF51822 based beacons, using the SWD interface. The docs recommended using the Segger J-Flash program, but that program is now...
Having a bizarre issue with mergehex and DFU. I hadn't had a problem with this previously with this code base. When I try and merge the App, Bootloader, Bootloader Settings...
we are working on a project which required to use usb cdc acm. compare with normal serial, the usb cdc acm always lost some packages when chip start and reboot. do anyone...
Hello,
I'm experimenting with nRF52840 Dongle and successfully flashed ble_zigbee_dynamic_color_light_bulb_thingy . I also connected it to my Samsung Smarthings hub (Zigbee...
Hello,
I am running application with softdevice s130 and nRF51_SDK v 12.2.0 on a custom board. The interrupts that are used by the SD are not used anywhere by the application...
platform:52840
Protocol stack:s14
IDE:keil v5.26
Hi,Master:
I want to simulate in a long time,I turned off the watchdog and also turned off the Bluetooth broadcast...
I want to use 52832 to measure the frequency offset and Modulation Characteristics in the advertising packet sent by Bluetooth slave.How can I do it? I think this information...
Hi All,
I am working on FOTA feature for Thingy91. My country is Vietnam and I only can use NB IoT to connect to cloud service.
I tested project FOTA example. My device...
The nRF52840 has a longer rx characteristic reception time than the nRF51822.
--> android terminal log
first and second line nRF52840 , It takes almost 1.2 seconds...
Dear All,
I need to know if there is anyway that I can update the data of the advertisement package of an iBeacon on the fly, while using Zephyr OS.
What I effectively...
Hello,
I've written a shell cmd on the 9160DK to send an sms. it handles getting the data in the correct has the following format,
sms <len> <pdu data>
I've used the...
hello,
I am trying to integrating ble_nus_init( ), inside ble_beacon_app, receiving through NUS_service and transmitting through beacon,
but program is stuck inside ble_advertising...
Is it possible to assign connection handles non-sequentially, for example based on the device's Bluetooth name? For the solution I'm developing I'd like for a given sensor...
Hi,
I am getting lots of transmission errors using the Serial library. I changed the Serial_Uartes example by removing the serial1 interface and creating a simple loopback...
