Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I have a very simple product which consists in a Xiao Nrf52840 board (which is FCC certified) wired to a 5v relay module. I was wondering if I would need additional FCC certification...
Hello, I am trying to add GPS functionality to my program running on the Thingy:91. However, I can't find any examples except for the Asset Tracker, which seems overly complex...
Hi,
MCU - nRF52832
I am trying to understand the power consumed during the PaWR operation. I am referring to the steps explained here: I am getting the a similar graph...
We currently have several nRF52840-based devices deployed in the field, running firmware developed using the nRF5 SDK and utilizing the SoftDevice S140 for BLE functionality...
Hi Team, I am trying to see the PaWR PDUs in wireshark sniffer. I am using example periodic_adv_rsp from NCS v2.9.0. I am referring to the link for exploring. How can I see...
Dear Nordic company,
I am writting to you in order to get some information about buffer sizes in your aplication. I think, I am bale to modify buffer size and maximum...
I am designing an application using the nPM1100 and I would like to know if I can use the VSYS as a power supply pin for my other circuit.
Is VSYS supplied by the battery...
In the nrf_sniffer_ble.sh script, the block that checks for an active virtual environment uses the following line:
if [ ! -z " $VIRTUAL_ENV "];
Notice that...
Previously, I compiled and downloaded the radio_test example into two DK boards.
I then used the CLI to set the parameters for each board one as TX one as RX
On setting...
1. Can we use SIM other than iBasis to use nrf cloud?
2. My SIM does not have a PUK. How to proceed without entering it.
3. We need SIM too kit document for nrf9161. ...
We are using the nrf52840-based module in our product.
This module is already certified with BT SIG.
Do we still need to certify our product with BT SIG certification...
Hi, As I am working on nRF5340dk and I am facing issues with flash memory. My application is exceeding the size of flash in nrf5340 (1MB flash). I want to move to nrf54 series...
This is a continuation of my previous thread ( Connections drop and don't come back (and "SoftDevice Controller ASSERT: 53, 296") ) (Case ID: 341823).
The project is a star...
Hello,
I am using Zephyr Toolchain v2.9.0 on an nRF9161 custom board . I have updated the modem firmware to mfw-nr+_nrf91x1_1.0.2 and flashed the board with the hello_dect...
Hi to you all. I have a question about how I can apply this mechanism in nRF52.
In modern TWS, it works like the phone or PC connects earbuds separately and sends and receives...
