I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi,
I am using Nordic nRF52840 SoC with nRF5_SDK_15.2.0_9412b96 (SDK) and S140 softdevice. I tried to set Tx power to +8dbm using
rc = sd_ble_gap_tx_power_set (BLE_GAP_TX_POWER_ROLE_ADV...
I am currently involved in developing a product that is using the nrf52840. The product needs to keep precise time across a wide range of temperatures, which is why a 32Mhz...
Hi,
When I try spi commnucation with sensor on nrf52840 (using Mbed OS with SDK14.2), it stuck to nrf_spim_task_trigger (p_spim, NRF_SPIM_TASK_START); while spim_xfer is...
Hi,
I am trying to increase the sampling rate of the motion sensor on a Thingy:52. I managed to update the firmware and increase the BLE_GAP_ADV_INTERVAL_MAX from 200 to...
I am using softdevice s132, nRF52832 and SDK 15.3
This happens every time I connect the RX line.
This is an application where I implement UART with the HRS application...
Hi,
I am interested to know how to make a mesh node (for example, a light server) compatible to perform a DFU.
I have gone through the DFU page and I noticed that the...
Hello.
I am about to receive the Uart service for the Nordic SDK Central and peripheral.
I Use nrf 52832.
In the peripheral example, we used 'ble_nus_data_send'...
Hi,
I am using nRF52840 Enineering C chip on a custom board using SDK v15.3.0 with SoftDevice v6.1.1
I have modified the Blinky Central code and the Blinky Peripheral...
Hi. After my nRF52832 peripheral connects to an android / iOS, I am trying to read the MTU size that has been negotiated with the following code;
current_mtu is being...
The NVMC writting functions hasn't return values,
void nrf_nvmc_write_bytes(uint32_t address, const uint8_t * src, uint32_t num_bytes)
Does it mean that all internal...
When nRF52840 P0.09 / P0.10 are used as GPIOs, the datasheet indicates they can be used for "low frequency I/O only". What is the frequency limit on these pins? Would it be...
Hello everyone, I come from taiwan.
I modify ble_app_multilink_central connect 8 heart rate watch to nordic nRF52832 board.
but i don't no how to create whitelist ,causes...
Hello, I am writing code for Nrf52832 using Segger Embedded studio. I want to store the data received from BLU NUS into a variable for further processing. So how can I store...
