Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi all,
Because of my customer special requirement ,I need two or three USB in my project .
But 52840 has one USB.Can I extend 52840 USB interface with a USB HUB?
With SDK V14.2, I was able to specify internal flash address argument into nrf_bootloader_app_start(uint32_t start_addr) and was able to boot into the address. With SDK V15...
Hello, I have a problem when trying to compile the light server exemple for the mesh.
I use Segger Embbeded Studio 4.16 (even though i tried the 4.15), mesh sdk 3.0 and...
Hello,
I'm using NRF52840 module to make a customer device. I'm using nRF5 SDK for Thread and Zigbee v3.0.0.
I have a Thread mesh with some routers devices and one child...
I saw this BLE security issue and was wondering how Nordic deals with it. When the other side uses the example LTK from the BLE spec, can the softdevice automatically reject...
Hi,
Here's I want to do: Use static passkey to connect with central and peripheral. I'm useing peer_manager to doing this. 1. I've setup passkey in peripheral with function...
Hi,
while I tried the Power Profiler in the nRF Connect Desktop on OS/X, I got some error messages in the log (something like PPK Command Error). So I've installed the newest...
I run blue_app_hids_keyboard_pca10056_s140 sample on nRF52840-DK. I try to connect with Windows 10 PC, but PC does not discover Nordic_Keyboard.
I found advertising is sent...
We have a PCA10090 board and I followed all the steps of the nRF Connect SDK to install everything, including the files from repository, SES, etc. All is ok but I can't find...
Hello, I am working on a project that uses nrf52832 and I need to put that device and in the system on mode. For that, I want to measure the current in the system on and system...
The PWM (Pulse Width Modulation) peripheral coupled with EasyDMA makes an excellent waveform generator. However it has one drawback which I would like to request be added...
Hi, i use the saadc example(triggered by ppi+timer) with uart to get voltage signal and transmit to central device( another custom nrf52832 board), and the central prints...
hi .eveyone. i use 51822 sdk12.3.0 , i want to dfu app code with uart, but not use bootloader_secure and experimental_ble_app_buttonless_dfu. i do not know how to develop...
Hi
Im trying to figure out how to migrate my quite large older project from and softdevice s130 to using s140 in order to experiment with long range.
Besides changing...
I try to update firmware for nrf9160.
My environment is windows10 msys2 python3.7.3 run follow, (not success) ----------------------------------------------------------...
